Synapse BMS-GW Series Скачать руководство пользователя страница 9

Страница: 9 / 52

SimplySNAP BMS Gateway/ProtoAir Start-up Guide

Page 9 of 52

PROTOAIR SETUP

3.1 Record Identification Data

Each ProtoAir has a unique part number located on the side or the back of the unit. This number should be
recorded, as it may be required for technical support. The numbers are as follows:

Model

Part Number

ProtoAir

FPA-W44-1620

Figure 1: ProtoAir Part Numbers

•

FPA-W44 units have the following 3 ports: RS-485 + Et RS-485

3.2

Configuring Device Communications

•

The device needs to be on the same IP subnet as the ProtoAir and the configuration PC.

•

Record the following device information:

IP Address

IP Port

Username

Password

NOTE: This information is required for Section

3.3

Attaching the Antenna

Wi-Fi Antenna:

Screw in the Wi-Fi antenna to the front of the unit as shown in

Figure 41

NOTE: Using an external antenna is also an option. An external antenna can be plugged into the

SMA connector. The best antenna for the job depends on the range, topography and
obstacles between the two radios.

Содержание BMS-GW Series





















































Результаты поиска

Содержание BMS-GW Series

Отзывы:

Похожие инструкции для BMS-GW Series

Бренды по названию

Популярные бренды

Synapse BMS-GW Series, Руководство для стартапов

Результаты поиска

Содержание BMS-GW Series

Отзывы:

Похожие инструкции для BMS-GW Series

Бренды по названию

Популярные бренды