Sym Jet Sport X R50 Скачать руководство пользователя

Страница: 170 / 181

15. Electrical Equipment

15-13

Oil Level Switch

Troubleshooting

If the oil level in oil tank is in specified level, but
the oil level indicator still goes on.

1. Remove luggage box.
2. Disconnect oil level switch wire, and turn the

main switch to ON position.

If there is no oil in oil tank or low oil level, but
the oil level indicator still not goes on.

3. Remove body cover.
4. Disconnect oil level switch wire and connect

a jump wire among coupler, and then turn
the main switch to ON position.

5. Disconnect oil level switch coupler, and check

voltage between wire and ground.

Removal/Installation

Remove luggage box.
Drain out oil from oil outlet tube.
Pull up oil level switch, and then remove oil level
switch from the oil tank.
Install the oil level switch in reverse order of
removal procedures.

Indicator light up

Indicator not light up

Short-circuit between
indicator and oil level

switch.

Malfunction of oil

level switch.

No voltage

Voltage

Open-circuit between
oil level switch and
indicator.

Blown bulb.

Indicator not light up

Indicator light up

Poor wire

connection.

Malfunction of oil

level switch.

Malfunction of oil level
switch.

Poor connection of oil
level switch.

Main switch

Oil level switch

Fuse

Indicator

Main switch

Oil level switch

Fuse

Indicator

Oil level switch

This chapter Contents

Содержание Jet Sport X R50






















































































































































































Результаты поиска

Содержание Jet Sport X R50

Отзывы:

Похожие инструкции для Jet Sport X R50

Бренды по названию

Популярные бренды

Sym Jet Sport X R50, Руководство по обслуживанию

Результаты поиска

Содержание Jet Sport X R50

Отзывы:

Похожие инструкции для Jet Sport X R50

Бренды по названию

Популярные бренды