background image

ү

CONNECTING SPREADER 

Connect the Spreader to the tow vehicle while 
the Spreader is empty. 

Remove the ½” Pin from the hitch stand. Lift 
the Spreader tongue and swing the Stand 
under the hitch bar so it is out of the way. 

Set the ball coupler on the 2” ball and push 
the coupler lock handle down. This locks the 
coupler to the ball. Insert the safety pin 
(

NB518

) into latch handle to keep the lock 

from accidentally unlatching during use. 

Swing the Stand up against the bottom of the 
hitch bar. Re-insert the previously removed 
½” pin into the lower hole to retain the stand 
in the up position. 

Level the Spreader. See 

page 13

for leveling 

instructions. 

CAUTION:  NEVER ATTEMPT TO MANUALLY MOVE, CONNECT OR 
DISCONNECT A FULLY LOADED SPREADER. 

12

GENERAL RECOMMENDATIONS

It is not recommended to tow behind a car 
or truck.

The Tow Hitch Bar is adjustable so the 
Control Handle can be reached from the tow 
vehicle.

Ensure the tow vehicle is rated to tow the 
weight of the loaded Spreader.

If the Control Handle is unreachable from 
the tow vehicle, refer to 

page 10

for 

instruction on adjusting the Hitch Bar length.

TOW VEHICLE REQUIREMENTS

The tow vehicle must be equipped with a 2” 
ball. 

The top of the 2” ball should be no less than 
11” and no more than 20” off the ground. 
Anything outside of this range will require 
additional equipment to raise or lower the 
ball height as needed so that the Hopper 
can be leveled.

FIGURE 12.1

FIGURE 12.3

SPREADER & TOW VEHICLE SET-UP

FIGURE 12.2

IMPORTANT SAFETY INFORMATION

ALWAYS Chock the Wheels of the Spreader 
so it cannot roll when not attached to tow 
vehicle. 

Always pin the Hitch latch closed to prevent 
the hitch from disconnecting unexpectedly.

Never Fill Hopper without the spreader 
being connected to a tow vehicle.

Содержание HOBBY FARM PRO 22000







































Отзывы: