Swing-N-Slide PB 8205 Скачать руководство пользователя страница 2

Safety Checklist for Swing-N-Slide Play Sets and Accessories

Installation Safety – Have You:

Consulted the assembly instructions supplied with your particular model?

Noted this accessory is to be used only on Swing•N•Slide approved designs? (Do not alter its design or add/remove components.)

Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.)

Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with 

a metal file as needed?

Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, garage,

house, overhanging branches, laundry lines, or electrical wires?

Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto

a hard surface can result in serious injury to the equipment user.)

Verified that suspended climbing ropes, chain,or cable are secured at both ends?

Consulted in assembly instructions of your particular model for minimum use zones?

Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply?

Made sure not to allow children to use equipment until it is properly installed?

Operating Safety – Have You:

Determined that on-site adult supervision is provided for children of all ages?

Warned children the following before allowing them to use the equipment?

Not to walk close to, in front of, behind or between moving items.

Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the

strength of chain or rope.

Not to swing empty seats or other accessories.

Be sure to sit in the center of the swing seat and other accessories with full weight on the seat.

Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not

limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard.

Not to use equipment in a manner other than intended.

Not to get off equipment while it is in motion.

Not to climb on the equipment when it is wet.

Determined that only one child per planned occupant seat should be allowed on this set at one time.

Determined children must be dressed appropriately for play. Avoid clothing with draw strings and loose fitting clothes which 

could become entangled or snagged on equipment.

Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself.

Read and understood the following warning regarding the use of two and four passenger lawn swings?

Warning: Lawn Swings are designed for use by children over two years of age. Use by children under the age of two can result

in entrapment between the seats and back areas. Never place children in a rearward facing position or with legs between the

seat and backrest because the child’s body may pass through the opening causing entrapment of the child’s head.

Safety Maintenance – Have You Determined to:

Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required? (It is 

particularly important that this procedure be followed at the beginning of each season.)

To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories and take indoors? (Do not 

use when the temperature drops below 0° F.)

Oil all metallic moving parts monthly during usage period?

Check all hardware and equipment for sharp edges twice monthly during usage season? (Replace when 

necessary.  It is especially important to do this at the beginning of each new season.)

Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration? Severe rusting or excessive

wear, especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in the protective plastic

sleeve or seat itself are also signs of deterioration. If any of these conditions exist, call 1-800-888-1232 to order replacement accessories.

Sand rusted metal parts and repaint using non-lead based paint. 

Disposal Instructions

When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards 

will exist at the time the set is discarded.

2

Important!  Additional Safety Instructions for all Swing-N-Slide Playground Equipment. 

Save this instruction sheet in the event the manufacturer needs to be contacted.

Observing the following statements and warnings reduces the likelihood of serious or fatal injury

R

Содержание PB 8205

















































Отзывы: