background image

SAFETY INSTRUCTIONS
INSTRUCCIONES DE SEGURIDAD
INSTRUCTIONS CONCERNANT LA SÉCURITÉ

REQUIRED SAFETY INSTALLATION INSTRUCTIONS

•  Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material

must be installed. 

This may be accomplished by using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission

“Handbook for Public Playground Safety” lists the following materials and required depths that are sufficient for home/residential application.

For fall height protection up to 9 ft. (2.742m) [recommended for Swing•N•Slide kits]:

When properly installed, shock absorbing material will completely

cover the horizontal baseboards on climbing units. This protective

surfacing must extend a 

minimum

of 6 ft. (1.828m) in all directions

from the perimeter of the equipment or from the outermost edges of

any component.  For example, a slide extending beyond the platform

must have protective surfacing at least 6 ft. (1.828m) out from both

sides as well as the end. For swings, the protective surface must

extend 

at least 14 ft.

out from

both

the back and front of the swing

when the swing is in its rest position.

IMPORTANT!

This product is intended for single family residential use only and not intended for use in any public

setting.  Placement in any public setting constitutes a misuse of this product.

LOOSE FILL MATERIAL

REQUIRED DEPTH 

1

INCH (mm)

(UNCOMPRESSED)

Wood Mulch

9"   (229mm)

Double Shredded Bark Mulch

9"   (229mm)

Uniform Wood Chips

12"   (305mm)

Fine Sand

12"   (305mm)

Fine Gravel

12"   (305mm)

1    These depths were derived from the CPSC Handbook. Swing•N•Slide

has not done independent tests to determine these required depths.

LʼUTILISATION DANS UN ENDROIT PUBLIC CONSTITUE UN USAGE ABUSIF DU PRODUIT.

•  Lorsque lʼunité est entiŹrement assemblée, un matériau de protection amortisseur doit źtre installé sur le sol avant de permettre aux

enfants de sʼamuser. 

Des matériaux particulaires dʼune épaisseur suffisante peuvent źtre utilisés ą cette fin. Le guide américain intitulé « Handbook

for Public Playground Safety » rédigé par la Consumer Product Safety Commission (CPSC) des États-Unis recommande une liste de matériaux et

spécifie lʼépaisseur requise pour un usage résidentiel. Protection contre les chutes dʼune hauteur de 9 pieds (2,742 m) [recommandation pour les

unités Swing•N•Slide] :

Pour que lʼinstallation soit adéquate, le matériau amortisseur doit

recouvrir entiŹrement la base horizontale des unités dʼescalade. Un

matériau de protection doit entourer lʼinstallation sur une surface 

dʼau

moins

1,828 m (6 pieds) ą partir du pourtour de lʼunité ou des

composants les plus éloignés. Par exemple, une glissoire qui se

prolonge au-delą de la plate-forme doit źtre pourvue dʼune surface de

protection dʼau moins 1,828 m (6 pieds) de chaque côté ainsi quʼą

lʼextrémité. En ce qui concerne les balanćoires, la zone de protection doit

couvrir 

au moins 14 pi (6 m)

autant devant que derriŹre la balanćoire

lorsque celle-ci est immobile.

IMPORTANT!

Ce produit est conću uniquement pour un usage résidentiel. Il ne saurait aucunement convenir aux

installations publiques.

MATÉRIAUX PARTICULAIRES ÉPAISSEUR RECOMMANDÉE

EN PO (mm) (NON COMPRIMÉ)

Paillis de bois

9 po   (229mm)

Paillis dʼécorce filamentée

9 po   (229mm)

Copeaux de bois uniformes

12 po   (305mm)

Sable fin

12 po   (305mm)

Gravier fin

12 po   (305mm)

1    Ces valeurs sont tirées du guide de la CPSC. Les unités Swing•N•Slide

nʼont pas fait lʼobjet dʼessais indépendants afin de déterminer lʼépaisseur

recommandée des matériaux.

INSTRUCCIONES REQUERIDAS PARA LA INSTALACIÓN CON SEGURIDAD

•  Una vez que se haya armado la unidad completamente y antes que se permita a los niĖos que la usen, se debe instalar un material

que amortigüe para la superficie del suelo. 

Esto se puede conseguir usando materiales que llenen flojamente a una profundidad suficiente.

El “Folleto para la Seguridad Pública en Campos de Recreo” de la Comisión de Seguridad de Producto al Cliente, permite los siguientes

materiales y las profundidades requeridas que sean lo suficiente para una aplicación en situaciones de residencias. Para protección contra

caídas se necesita hasta 9 pies (2,742m) [recomendadas para los conjuntos Swing•N•Slide]:

Cuando se instale apropiadamente, el material que amortigüe

completamente cubrirá la base horizontal de las unidades de trepar.

Esta superficie protectora debe extenderse un 

mínimo

de 6 pies

(1,828m) en todas las direcciones desde el perímetro del equipo, o de

los bordes más salientes de cualquier componente. Por ejemplo, un

tobogán que se extiende más allá de la plataforma debe tener una

superficie protectora de por lo menos 6 pies (1,828m) más allá de

ambos lados, al igual que desde el extremo. Para columpios, la

superficie protectora debe extenderse 

por lo menos 14 pies

más allá

de 

ambos,

de la parte de atrás, y la parte frontal del columpio, cuando

el columpio esté en una posición neutra.

ŃIMPORTANTE! 

Este producto es para ser usado por una sola familia en uso residential y no para usarse en

ningún lugar público. El ubicarlo en cualquier lugar público constituye mal uso de este producto.

MATERIAL DE APLICACIÓN FLOJA

PROFUNDIDAD REQUERIDA

1

PULGADA

mm (SIN SER COMPRIMIDA)

Viruta de madera

9"   (229mm)

Viruta trizada de corteza de árbol  9"   (229mm)

Trozos pequeĖos uniformes

de madera    

12"   (305mm)

Arena fina

12"   (305mm)

Grava fina

12"   (305mm)

1    Estas profundidades fueron derivadas del folleto CPSC. Swing•N•Slide no

ha hecho pruebas independientes para determinar las requeridas profundidas.

3

Meijer.com

Содержание Alpine 611





































Отзывы: