70
MV-1930/1931-06-2021 . © Alle rettigheder forbeholdes Swim & Fun A/S
UK
Installation with a sandwich gasket
Fill the pool up to approx. 5 cm below the skimmer perforation. Carefully
cut out an equivalent hole from the perforation in the pool wall. Install the
gasket in the skimmer perforation in the wall
so that it rests on both
the liner and the pool wall
. Watch to see that it aligns correctly with the
screw holes on all four sides. Now, from the inside, fasten the skimmer’s
inner frame to the skimmer housing with screws.
8. Information concerning the installation of an in-ground
swimming pool
In general, our steel wall pools are designed to be used above-ground in the garden. It should therefore be
noted that the product warranty does not cover damage caused by improper installation or if the pool is used
as an in-ground installation. If you wish to use the pool in-ground we recommend contacting a pool profes-
sional to handle this task.
If you wish to use the pool in-ground, the following important advance steps must be followed:
Location:
Check with your local authorities whether any permission is required to place a pool in the desired location.
It is recommended that you always contact your insurance company before you build and install a your pool.
As the owner of the pool, you are obliged to inform your insurance company that you have a pool on your
property.
Preparation:
Select the area where you want the pool to be situated.
For round pools, the installation area should be 1 metre wider in diameter than the pool itself. For oval pools,
the area must be one metre longer than the length of the pool and two metres wider than the width of the
pool.
Base:
The base of the pool must be completely level and 100% solid. Never install a pool on a base which is not
firm and solid; this can cause the pool construction to become unstable because of the weight of the water.
Remember that 1000L => 1m3 => 1000 kg! There must not be any holes in the base, small rocks, pebbles,
plants or roots that could puncture the liner.
We recommend pouring a net-enhanced concrete base with a thickness of 15 cm. This base should be com-
pletely smooth and 100% level.
To protect the liner, always position a ground cover on top of the concrete base. In addition, you can also
position a layer of insulating bottom sheets in 50 mm hard EPS material.
Choose a sunny location for the pool which is also close to water, drainage and electricity.
Do not place the pool above electric cables, gas cables, or in areas with high levels of groundwater.
Do not place the pool under electric cables in the air.
Select a location that offers shelter and where there are no trees in the immediate vicinity, or leaves will con
-
tinuously land in the pool. Position the in-wall skimmer so that the wind will blow towards it.
Remember that the filter and the pump of the pool must
always be installed so that it is level with the pool
bottom.
Содержание KRETA XL POOL 1930
