manualshive.com logo in svg

SWH Solar Racking, Руководство по установке

Поделиться
Скачать
SWH Solar Racking Скачать руководство пользователя страница 8

9628 Valley Blvd. Rosemead, CA 91770  | Phone 626-579-3288  | [email protected]

SWH  Solar Racking Installation Guide | Version 12.10.v2

8

Notes:

1. Values are design 3-second gust wind speeds in miles per hour (m/s) at 33 ft (10m) above ground for Exposure C category.
2. Linear interpolation between contours is permitted.
3. Islands and coastal areas outside the last contour shall use the last wind speed contour of the coastal area.
4. Mountainous terrain, gorges, ocean promontories, and special wind regions shall be examined for unusual wind conditions.
5. Wind speeds correspond to approximately a 3% probability of exceedance in 50 years (annual exceedance probability = 
0.000588, MRI = 1700 years).

Miles per hour (Meters per second)

Source: ASCE 7-10 Minimum Design Loads for 
Buildings and Other Structures, Chapter 26

[1.2.] Procedure to Calculate Total Design Wind Load per ASCE 7-10

FIGURE 26.5-1B  Basic Wind Speeds for Risk Category III and IV Buildings and Other Structures

Содержание Solar Racking








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды