manualshive.com logo in svg

SWH Solar Racking, Руководство по установке

Поделиться
Скачать
SWH Solar Racking Скачать руководство пользователя страница 26

[3.2.1] Planning your SWH installations

The installation can be laid out with rails parallel to 

the rafters or perpendicular to the rafters. Note 

that SWH rails make excellent straight edges for 

doing layouts. Center the installation area over the 

structural members as much as possible. Leave 

enough room to safely move around the array 

during installation. Some building codes require 

minimum clearances around such installations, and 

the user should be directed to also check ‘The Code’.

 

The width of the installation area equals the length 

of one module.

The length of the installation area is equal to:

• the total width of the modules,

• plus 1/4 inch for each space between modules for 

grounding mid clamp or 1 inch for standard mid clamp,

• plus 3 inches (1

½ inches for each pair of end clamps). 

Figure 6. Rails may be placed parallel or perpendicular to rafters.

Rail cantilever/overhang span shall NOT exceed 25% of footing attachment spacing

9628 Valley Blvd. Rosemead, CA 91770  | Phone 626-579-3288  | [email protected]

SWH  Solar Racking Installation Guide | Version 12.10.v2

26

Содержание Solar Racking








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды