manualshive.com logo in svg

SWH Solar Racking, Руководство по установке

Поделиться
Скачать
SWH Solar Racking Скачать руководство пользователя страница 30

[3.2.5] Flashed L-feet Installation

REQUIRED INSTALLATION TOOLS: Tape measure, chalk line, stud finder, caulking gun, sealant compatible with roofing 

materials, drill with 1/4” long-style bit, socket wrench or impact gun with 5/16” deep socket

1

3

4

6

STEP 1: Locate the rafters and snap hori-

zontal and vertical lines to mark installation 

position for each flashing.

STEP 4: Line up pilot hole with high profile 

L-feet hole.

STEP 2: Drill a pilot hole (1/4” diameter) 

for the lag bolt. Backfill with sealant. 

STEP 5: Insert lag bolt through L-feet, 

flashing and pilot hole.

STEP 3: Insert the flashing so the top 

part is under the next row of shingles and 

pushed far enough up slope to prevent 

water infiltration through vertical joint in 

shingles. Line up flashing hole with pilot 

hole.

STEP 6: Tighten lag bolt to 100-140 

torque inch pounds depending on the 

type of wood and time of year.  If using an 

impact gun be careful to not over torque 

the fastener. You may need to stop and 

use a hand ratchet to finish the installation.

5

2

 WARNING: Flashed L-feet Products are NOT designed for and should NOT be used to anchor 

fall protection equipment

9628 Valley Blvd. Rosemead, CA 91770  | Phone 626-579-3288  | [email protected]

SWH  Solar Racking Installation Guide | Version 12.10.v2

30

Содержание Solar Racking








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды