Swegon RX/HC Скачать руководство пользователя страница 2

GB.FUNKRXHC.180907

We reserve the right to alter specifications.

2    www.swegon.com

3. Function 

3.1 General

RX/HC has a reversible heat pump function that is con-
trolled by the GOLD air handling unit’s control system 
IQlogic via bus communication to the refrigerant circuit’s 
control system iPro. 

Operation and setting occurs via the GOLD air handling 
unit’s hand-held micro terminal (see section 5. Settings). 

The reversible heat pump circuit is controlled  
with three signals:
• Stop/Start (0/1)
• Heating/Cooling (0/1)
• Speed level compressor in per cent (25-100%)

When operation is requested, a start signal is sent for the 
production of heating or cooling. 

Depending on the need in question, a signal is also sent 
for the operating level, 25-100%. When operation is 
not required, a stop signal is sent and 0 % signal for the 
operating level.

3.2 Start of RX/HC air handling units

Start of the reversible heat pump occurs after the GOLD 
air handling unit’s ordinary start sequence. Operation of 
RX/HC is blocked during the GOLD air handling unit’s 
ordinary start sequence. 

3.3 Stop of RX/HC air handling unit

When stopping the GOLD air handling unit, operation of 
the reversible heat pump is shut down immediately. 

Post-cooling of the refrigerant circuit and electric air 
heater for defrosting (if fitted) is carried out. After cooling 
is in progress two minutes after the last operation of the 
compressor or electric air heater.

3.4 Temperature regulation

The heat pump has its own control sequence (HC) in the 
GOLD air handling unit’s temperature sequence. The 
sequence regulates the temperature requirement 0-100%, 
for the heating and cooling sequence respectively. 

The heat pump is enabled when the temperature require-
ment exceeds 3% for 60 seconds and is disabled when 
the temperature requirement drops below 1% for 60 
seconds (applies for Operating mode - Standard).

Size 011 - 035 (one compressor)

The refrigerant circuit contains a speed controlled com-
pressor.

The compressor works between a MIN level (normal 25%) 
and maximum speed.

At a temperature requirement below 25% the compressor 
is run at 25% of max, at a need above 25% the compres-
sor follows the temperature requirement. (see the diagram 
below)

3

 

25%

%

%

 

25% 

100 %

 

100 % 

%

1

 

Temperature require-
ment, GOLD
Operation level, HC

Temperature requirement

Compressor operation

Содержание RX/HC









Отзывы: