www.S
noBiz
.com
1(800)-
742-8342
4
SWAN SI-100E OWNERS MANUAL
2020.1
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
4
www.SwanIceShavers.com
-
1-888-353-3719
-
4. Turn on the Motor Switch. The Main Shaft Ice Block Holder will start to revolve. If ice block wobbles as it rotates, turn off
power switch and re-center the ice block.
5. Turn the Blade Adjustment Knob located on the left side of Shaving Plate Frame counter
-
clockwise SLOWLY. This will
raise the blade, allowing it to shave the ice. The higher the blade is raised, the coarser and faster the ice will come out.
6.
After the texture of shave ice is adjusted, hold the cup under the outlet of shave ice.
7.
Turn off Motor Switch after use.
8.
Turn
the
Ice Block Holder Crank clockwise
to
raise
the
Main Shaft Ice Block Holder.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
3
www.SwanIceShavers.com
-
1-888-353-3719
-
•
Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick, this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•
Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn
the
Ice Block Holder Crank clockwise
to
raise
the
Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2.
Make sure that the blade is in the down position, below the
S
having
P
late opening.
Place ice block flat side up, and center
on the
s
having
plate
. This may require a couple of tries.
3. Turn
the
Ice Block Holder Crank
counter-
clockwise
to
lower
the
Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded in the ice. The polycarbonate shield should be turned horizontally to the
front.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
3
www.SwanIceShavers.com
-
1-888-353-3719
-
•
Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick, this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•
Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn
the
Ice Block Holder Crank clockwise
to
raise
the
Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2.
Make sure that the blade is in the down position, below the
S
having
P
late opening.
Place ice block flat side up, and center
on the
s
having
plate
. This may require a couple of tries.
3. Turn
the
Ice Block Holder Crank
counter-
clockwise
to
lower
the
Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded in the ice. The polycarbonate shield should be turned horizontally to the
front.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
4
www.SwanIceShavers.com
-
1-888-353-3719
-
4. Turn on the Motor Switch. The Main Shaft Ice Block Holder will start to revolve. If ice block wobbles as it rotates, turn off
power switch and re-center the ice block.
5. Turn the Blade Adjustment Knob located on the left side of Shaving Plate Frame counter
-
clockwise SLOWLY. This will
raise the blade, allowing it to shave the ice. The higher the blade is raised, the coarser and faster the ice will come out.
6.
After the texture of shave ice is adjusted, hold the cup under the outlet of shave ice.
7.
Turn off Motor Switch after use.
8.
Turn
the
Ice Block Holder Crank clockwise
to
raise
the
Main Shaft Ice Block Holder.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
3
www.SwanIceShavers.com
-
1-888-353-3719
-
•
Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick, this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•
Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn
the
Ice Block Holder Crank clockwise
to
raise
the
Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2.
Make sure that the blade is in the down position, below the
S
having
P
late opening.
Place ice block flat side up, and center
on the
s
having
plate
. This may require a couple of tries.
3. Turn
the
Ice Block Holder Crank
counter-
clockwise
to
lower
the
Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder prongs are firmly imbedded in the ice. The polycarbonate shield should be turned horizontally to the
front.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
3
www.SwanIceShavers.com
-
1-888-353-3719
-
•
Be careful not to touch a metal ice pick to the Aluminum shaving plate. If scratching occurs from the ice pick, this will
cause the ice shavings to be uneven and produce “pitting”. This can also result in metal shavings and damage the plate.
•
Unplug machine when not in use.
DIRECTIONS BEFORE USE
The Ice Block Holder Crank is detached from the machine and packed together so it must be installed. Insert Ice Block
Holder Crank onto Shaft Pin located on the right side of machine, then firmly tighten screw in the center.
OPERATION DIRECTIONS
1. Turn
the
Ice Block Holder Crank clockwise
to
raise
the
Main Shaft Ice Block Holder. The Polycarbonate shield should be
turned horizontally to the rear.
2.
Make sure that the blade is in the down position, below the
S
having
P
late opening.
Place ice block flat side up, and center
on the
s
having
plate
. This may require a couple of tries.
3. Turn
the
Ice Block Holder Crank
counter-
clockwise
to
lower
the
Ice Block Holder onto ice. Apply pressure until the Ice
Block Holder
prongs are firmly imbedded in the ice. The polycarbonate shield should be turned horizontally to the
front.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
5
www.SwanIceShavers.com
-
1-888-353-3719
-
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1.
The Blade is recessed below the surface of the Shaving Disc when the Blade Adjustment Dial is turned to 0.
2.
To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3.
Set the Blade Adjustment Dial on 1 for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0 WHEN THE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1.
Turn the Blade Adjustment Knob right all the way until it stops.
2.
Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3.
Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4.
Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
