www.S
noBiz
.com
1(800)-
742-8342
6
SWAN SI-100E OWNERS MANUAL
2020.1
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1.
Remove the rubber plug on the front of the head cover.
2.
Raise Ice Block Holder Crank Clockwise.
3.
Take a straight edge screwdriver and turn Brake Adjustment Screw counterclockwise, slowly.
4.
When the Ice Block Holder Crank drops, stop.
5.
Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6.
Test the pressure of the Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug in cord and push
the protector. The Motor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1.
By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2.
To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3.
Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the Main Shaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x 11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor: 115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1.
Remove the rubber plug on the front of the head cover.
2.
Raise Ice Block Holder Crank Clockwise.
3.
Take a straight edge screwdriver and turn Brake Adjustment Screw counterclockwise, slowly.
4.
When the Ice Block Holder Crank drops, stop.
5.
Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6.
Test the pressure of the Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug in cord and push
the protector. The Motor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1.
By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2.
To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3.
Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the Main Shaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x 11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor: 115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
5
www.SwanIceShavers.com
-
1-888-353-3719
-
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1.
The Blade is recessed below the surface of the Shaving Disc when the Blade Adjustment Dial is turned to 0.
2.
To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3.
Set the Blade Adjustment Dial on 1 for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0 WHEN THE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS
PRODUCING ICE.
BLADE REPLACEMENT
1.
Turn the Blade Adjustment Knob right all the way until it stops.
2.
Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3.
Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4.
Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
5
www.SwanIceShavers.com
-
1-888-353-3719
-
9. If ice block wobbles as it rotates, turn off power switch and re-center the ice block.
10. Remove the ice block.
BLADE ADJUSTMENT
1.
The Blade is recessed below the surface of the Shaving Disc when the Blade Adjustment Dial is turned to 0.
2.
To raise the Blade, slowly turn the Blade Adjustment Knob counter-clockwise.
3.
Set the Blade Adjustment Dial on 1 for fine shaving and 6 for roughest shaving.
Note: THE DIAL WILL INDICATE 0 WHEN THE BLADE ADJUSTMENT KNOB IS TURNED CLOCKWISE ALL THE WAY AND
STOPS PRODUCING ICE.
BLADE REPLACEMENT
1.
Turn the Blade Adjustment Knob right all the way until it stops.
2.
Unscrew the two Phillips-screws. Remove the Blade Holder and blade.
Important: DO NOT INTERFERE WITH THE CENTER SLOTTED SCREW.
3.
Place the new Blade accurately on the Standard Level Guide Screws on the Blade Support.
4.
Put the Phillips-screw in and slowly screw it on so the blade will not lift up from the Standard Level Guide Screws.
Screw it on tight.
*If both ends of the Blade are not accurately set on the Standard Level Guide Screws, the ice will not shave correctly.
OWNERS MANUAL
2019.09
SwanIceShavers.com
1-888-353-3719
6
BRAKE ADJUSTMENT-Adjust when ice is not shaving correctly.
1.
Remove the rubber plug on the front of the head cover.
2.
Raise Ice Block Holder Crank Clockwise.
3.
Take a straight edge screwdriver and turn Brake Adjustment Screw counterclockwise, slowly.
4.
When the Ice Block Holder Crank drops, stop.
5.
Turn Brake Adjustment Screw clockwise with screwdriver 2-2.5 full turns.
6.
Test the pressure of the Crank. It should be firm to turn.
PROTECTOR
A Push Button Switch (Protector) is located on the left side of the Head Cover. If something is wrong with the blade
section or the revolving section, the machine will automatically stop to prevent overheating and damage the motor. In
such case, turn off the Power Source Switch (Disconnect the plug) and after the cause is removed. Plug in cord and push
the protector. The Motor will automatically start again.
TO MAINTAIN SANITATION WITHOUT TOOLS
For periodic cleaning of the Shaving Plate as well as adjacent area in the food zone, removal is possible as follows.
1.
By removing the 4 thumbscrews located on the underside of the plate, the Shaving Plate can be easily removed
by pushing it up.
2.
To clean the Shaving Plate Frame and the adjacent area, remove the 4 thumbscrews holding the Front Cover (2
thumbscrews on each side), then pull the Front Cover towards the user to remove. The entire food zone can be
easily cleaned.
3.
Brake Shoe and worm gear should not have any grease on the metals. This is caused by Hot weather conditions
and heavy use of the shaver. Simple use a dry rag, turn the machine on, and wipe the parts clean.
STORAGE AFTER SEASON
Wipe off moisture with piece of cloth, then wipe again with dry piece of cloth. Remove Blade, clean and lubricate
with cooking oil, the wrap in foil paper before storage. Remove all soiled oil from the Main Shaft and lubricate with
grease approved by FDA for the lubrication of food processing machinery. Do not use cooking oil. ALWAYS unplug the
machine when not in use.
SPECIFICATIONS*
Dimensions: 25-3/4” high x 11-1/8” wide x 15-1/8” deep
Weight: 61.7 lbs.
Shaving Capacity: 4.84 to 5.5 lbs. per minute
Motor: 115V, 200W
Power Requirement: 210W, 60Hz
Accessories: Spare Blade (1), Grease oil (1), Drain Hose (1)
*Specifications are subject to change without notice for further design and performance improvement.
TUNE-UP KITS & COMPLETE MAINTENANCE
VIDEOS ARE AVAILABLE AT:
