Suzuki RM-Z450 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 121

background image

5-5

When the Engine is already
Warm or Restarts:

Kick down the kick starter lever
slowly from the top position until
engine compression resistance is
felt, release the kick starter lever
from this position and allow it to
return to the top. While keeping
the throttle closed, depress the
kick starter lever strongly through
the full stroke. Never open the
throttle during the kick start oper-
ation.

NOTE: If the engine fails starting,
open the throttle fully and depress
the kick starter lever slowly about
4 – 5 times to clear too rich fuel
mixtures in the engine. Then, kick
the engine over, leaving the throt-
tle closed.

* If the engine is not started even

after taking the above proce-
dure, pull out the starter knob
for starting the engine. When
the engine is started, push
back immediately the starter
knob.

Conditions when the starter knob is used

Engine condition

Starter knob

Warm engine

Push back (OFF)*

Cold engine

Pull out (ON)

«
...
48
49
50
51
52
...
»

Содержание RM-Z450


























































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z450

Бренд: DAELIM Страницы: 2

Бренд: yasuni Страницы: 8

Бренд: KYMCO Страницы: 424

Бренд: hepco & becker Страницы: 5

Бренд: CF MOTO Страницы: 443

Бренд: MRA Страницы: 6

Бренд: DYNATEK Страницы: 12

Бренд: DYNATEK Страницы: 12

Бренд: Mastech Страницы: 2

Бренд: LSL Страницы: 4

Бренд: Wunderlich Страницы: 4

Бренд: HYOSUNG Страницы: 74

Бренд: VOIGT MT Страницы: 2

Бренд: X-TREME Страницы: 6

Бренд: Hobart Страницы: 16

Бренд: hepco & becker Страницы: 3

Бренд: Rothewald Страницы: 60

Бренд: APRILIA Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды