Suzuki RM-Z450 Скачать руководство пользователя страница 89

Страница: 89 / 121

6-30

Inspecting the Drive Chain

When inspecting the chain, look
for the following:
•

Loose pins

•

Damaged rollers

•

Dry or rusted links

•

Kinked or binding links

•

Excessive wear

•

Improper chain adjustment

If you find anything wrong with the
drive chain condition or adjust-
ment, correct the problem if you
know how. If necessary, consult
your authorized Suzuki dealer.

Good

Worn

Damage to the drive chain means
that the sprockets may also be
damaged. Inspect the sprockets
for the following:
•

Excessively worn teeth

•

Broken or damaged teeth

•

Loose sprocket mounting nuts

NOTE: The two sprockets should
be inspected for wear when a new
chain is installed and replaced if
necessary.

If you find any of these problems
with your sprocket, consult your
Suzuki dealer.

Drive Chain Cleaning and
Oiling

Clean and oil the chain as follows:
1. Remove dirt and dust from the

drive chain.

2. Clean the drive chain with a

drive chain cleaner, or water
and neutral detergent.

3. Use a soft brush to clean the

drive chain.

4. Wipe off water and neutral

detergent.

5. Lubricate with a motorcycle

drive chain lubricant or high
viscosity oil (#80 – 90).

6. Lubricate both front and back

plates of the drive chain.

7. Wipe off excess lubricant after

lubricating all around the drive
chain.

NOTICE

Cleaning the drive chain
improperly can damage ruin
the drive chain.

• Do not use a volatile solvent

such as paint thinner, kero-
sene and gasoline.

• Do not use a high pressure

cleaner to clean the drive
chain.

• Do not use a wire brush to

clean the drive chain.

Содержание RM-Z450


























































































































Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды

Suzuki RM-Z450, Руководство пользователя

Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды