Suzuki RM-Z450 Скачать руководство пользователя страница 52

Страница: 52 / 121

5-7

S-HAC MODE

Engine control release conditions

When any of the above conditions are met, the active mode is released
and the normal mode is selected.

Mode (Indicator light)

Use for

Normal mode (Unlit)

–

Mode-A (slow flashing)

Hard & dry dirt, or concrete base

Mode-B (fast flashing)

Normal dirt

Selected

mode

Engine control release conditions

Mode-A

Mode-B

Control released 6 seconds after starting begins.

Control released when throttle is closed after starting begins.

Control released upon shift to 5th gear.

Control released if starting off is not performed within 180 seconds after mode-
A or mode-B is selected.

Released when the S-HAC switch is pressed again and held down until indica-
tor light turn off.

Содержание RM-Z450


























































































































Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды

Suzuki RM-Z450, Руководство пользователя

Результаты поиска

Содержание RM-Z450

Отзывы:

Похожие инструкции для RM-Z450

Бренды по названию

Популярные бренды