29
8.4
CPM2 Operating Mode
8.4.1 CPM2 Cold Startup
The “cold boot” should be performed to install the
default system software. Follow the procedure
described here to perform a “cold boot” of the CPM2.
Remove the CPM2 from the card cage.
Turn the “PROG EN” (Program Enable) switch ON. The
Program Enable switch is located on the left side of
the CPM2 unit; use a small screwdriver to turn the
switch ON by turning it clockwise.
Reinstall the CPM2 in the card cage, but do not fasten
the mounting screws. The CPM2 should power up
and this message will be displayed:
SYST COLD BOOT?
Ent=Yes Bsp=No
Press the [Enter] button to perform the “cold boot.”
This message will be displayed:
SYST COLD BOOT
Executing!
After approximately 1 second, this message will be
displayed:
Please Turn Off
Program Switch!
The CPM2 will remain in an inoperative mode until the
Program Enable switch is turned OFF.
• Pull the CPM2 part way out of the card cage
• Use a small screwdriver to turn the Program Enable
switch OFF by turning it counterclockwise.
• Reinstall the CPM2 in the card cage and secure the
faceplate screws
The CPM2 is now ready for operation. Set the clock
and calendar and configure the CPM2.
8.4.2 CPM2 in Standby Mode
When the CPM2 is in Standby mode, a message simi-
lar to this will be displayed:
*FEB-23 07:30:45
Scanning 1E (30)
This indicates that the system is ready to receive data
from the line cards and input from the numeric key-
pad and push buttons.
8.4.3 CPM2 Configuration Mode
The Configuration mode allows programming of the
various features and options available on the CPM2.
To enter the Configuration mode, press the [Escape]
button; this message will be displayed:
Enter MASTER-ID
....
Enter the Master Access Code using the keypad; the
default Master Access Code is “CAFE.” When the
access code is entered, the screen will display the first
option in the Options menu:
01:Sys Date/Time
Ent:+ Bs:- Ack:S
Press the [Enter] button to display the next menu
item, or press the [Backspace] button to display the
previous menu item; press the [ACK] button to select
the menu item presently displayed on the screen.
8.4.4 Configuration Options
The CPM2 features 28 configuration options:
01
System Date and Time
02
System Passwords
03
Number of Line Cards
04
Printer Select
05
COM1 Configuration
06
COM1 Format
07
Acknowledge Wait Delay
08
Heartbeat Select
09
COM2 Configuration
10
COM2 Format
11
Contrast Adjust
12
UL Receiver Option
13
Erase Memory
14
Mute Buzzer
15
Keep Last Message
16
Debug ComPort
17
Test 9v/12v Batt
18
Debug Line Card
19
Program Version
20
Monitor Battery
21
Year / Second
22
Force Reset
23
Change Receiver Number
24
Scada COM1 and COM2 Control
25
Printer Control
26
Printer Test
27
Printer Width
28
Tamper Input
Option 01: Setting the Clock
Option [01] allows the CPM2 date and time to be set.
Press the [ACK] button when the “01: Sys Date/Time”
message is displayed; this message will be displayed:
(D/M/Y) 23/02/93
(H:M:S) 07:30:45
Enter the date and time using the numbers 0 through
9 only. Press the [Enter] button to move the cursor
one character to the right; press the [Backspace] but-
ton to move the cursor one space to the left. When
the date and time are entered, press the [Escape] but-
ton; when the [Escape] button is pressed, the next
Configuration option will be displayed on the screen.
Note that if “0” or a number greater than “12” is pro-
grammed for the month, the screen will display the
word “Nul” in place of the month while in the Standby
mode. “Nul” will also be displayed for the time if the
time has not been programmed properly.
Option 02: Changing System Passwords
Option [02] allows the CPM2 passwords to be
changed or erased. Press the [ACK] button when the
“02: Sys Passwords” message is displayed; this mes-
sage will be displayed:
PassID#0: xxxx
Operator: S.G.
Содержание MLR2E
Страница 2: ......
