Sur-Gard MLR2000, Руководство по установке

Страница: 25 / 52

21
The DRL2000 will interpret this information as 1234
301. Note that a longer on-line time is required for this
format than for a standard 4/2 format. The default set-
ting for Option [97] is '00'; when programmed as '00',
the option is disabled.
Option [98]: 3/1 Extend - Default [01]
Program Option [98] as '01' to combine 2 round pairs of 3/
1 extended or 3/1 partial extended format into 3/2 output
for reporting to the computer and the printer. For example,
with Option [98] enabled, the security control panel may
transmit the following information:
123
123
333
333 3
3
1
1
The DRL2000 will interpret this information as: 123 31;
the default setting for Option [98] is '01'; when pro-
grammed as '00', the option is disabled.
Option [99]: Ademco Express - Default [01]
The Ademco 4/1 Express format may cause conflicts
with the Sur-Gard DTMF 4/3 with checksum format or
FBI Super fast without checksum. Therefore, this option
must be programmed to inform the DRL2000 which of
the 3 formats may be used.
00
01
02 Sur-Gard DTMF 4/3 with checksum
Ademco 4/1 Express
FBI without checksum
Option [9A]: Error Counter - Default [00]
Program this option to determine the number of bad
rounds from a pulse communicator the line card will
receive before hanging up.
Option [9B]: Echo Canceller - Default [00]
00
01 Disabled
Enabled: The echo suppression option will enable the
transmission of a two-second 2025 Hz tone from the
line card to disable echo suppression equipment.
Option [9C]: Acron RS-232 - Default [01]
When this option is programmed as '00', the DRL2000
will convert the Acron Super Fast format signal into 3/2
or 4/2 format (Ex: AAAAsXssYY[DC4] ). If it is pro-
grammed as '01' the Acron Super Fast will be sent to
the computer as indicated below:
9RRLLLssssAAAACCCCCCCCC[DC4]
Where 9 = protocol number
RR = receiver number
LLL = line number
ssss = spaces
AAAA = account code
CCCC = channel 1-4
CCCC = channel 5-8
[DC4] = terminator
Option [9D]: MODEM II RS-232 - Default [01]
The DRL2000 is able to decode the Modem II formats.
The handshake 0B needs to be programmed as one of
the handshakes of the DRL2000 for the Modem II and
handshake 0E for Modem IIE or Modem IIIa
2
. Option
[9D] determines the protocol sent to the computer. Note
that this option will also affect the BFSK format only if
programmed as 00 or 01.
00
01
02
03 6500 protocol: 1RRLLLssssssAAAAXXYYYY[DC4]
SG protocol: 6RRLLLssssssAAAAXXYYYY[DC4]
ModemII to SIA protocol
ModemII to SIA protocol, and text is decoded and sent
to printer and computer.
NOTE: Ensure that the automation software sup-
ports settings 02 and 03 if the SIA protocol is
desired.
Option [9E]: Reserved
Option [9F]: Ademco High Speed RS-232 - Default
[01]
When this option is programmed as '00', the DRL2000 will
convert the High Speed format signal into 4/2 format (E.g.
1RRLLLssssssAAAAsXssYY[DC4
] ). If it is programmed as
'01' the Ademco High Speed will be sent to the computer
as indicated below:
8RRLLLAAAAsCCCCsCCCCsC[DC4]
Where 8 = protocol number
RR = receiver number
LLL = line number
AAAA = account code
CCCC = channel 1-4
s = space
CCCC = channel 5-8
s = space
C = Channel 9
[DC4] terminator
Option [A0]: Reserved
Option [A1]: FBI RS-232 - Default [01]
To enable the computer for FBI Super Fast protocol, pro-
gram Option [A1] as '01'. When enabled, the computer
output will be as indicated below:
JRRLLLssssssAAAATZZEss[DC4]
Where:
J = FBI protocol identifier
RR = receiver number
LLL = line number
s = spaces
AAAA = account code
T = zone type
ZZ = zone number, in hex.
E = event code
if E = 0 and T = 0 : listen in.
Option [A2]: Digit Replace - Default [00]
Option 77 works in conjunction with Option A2. Option
77 is programmed with an ASCII value that will replace
an account code digit or insert a value into an account
code. Option A2 is used to replace a digit or insert a
digit. To replace a digit use 0x where x is the digit to be
replaced. To shift a digit use Option A2 and set to 8x
where x is the location in the account code.
Option [A3]: D6500 RS-232 - Default [00]
This option is used to strip hex digits on the automation
output. The DRL2000 will emulate the Radionics 6500 RS-
232 protocol on pulse formats and Varitech only. When
Option A3 is set to 01 the hex digit will be stripped for 1-
digit reporting codes including Varitech 4/1.
Example 1 : Code 1
Computer output: 104091sssssss022sAsss1
Example 2 : Code B
Computer output: 104091sssssss022sOssss
If Option A3 set to 02: the hex digit will be stripped for
2-digit reporting codes including Varitech 4/2.
Example 1 : Code 21
Computer output: 104091sssssss022sAss21
firealarmresources.com