USE
- Unwind the cable completely before connecting it.
- Connect the unit to the mains.
- Position the unit to direct the air flow in the desired direction.
- Switch the unit on by pressing the on/off button(
h
).
Commandes faciles à utiliser
Suitable for 20 m².
An economical way to combat mildew, condensation and moisture.
Dries clothes more efficiently than a tumble dryer.
Designed to fit into any modern space
Castors for easy mobility
Intelligent CPU-controlled digital humidistat with display of room humidity and relative humidity
between 35 and 80%.
24 hour start/stop timer
Tank operation or permanent drainage option with anti-splash tank Full tank alarm and auto shut-off
function
1.
2.
3.
4.
5.
6.
7.
8.
9.
g. Power button to turn on/
off the unit
e.
MODE
button
Selects the function of the appliance between ECO and FAN modes. The
LEDs next to the button indicate the selected mode. ECO MODE : The
appliance defaults to ECO mode when first switched on and remains in this
mode until another programme is selected.
another programme is selected. In ECO mode, it defaults to a relative
humidity of 50-55%.
Air purifier: Only the fan operates and no water is extracted.
a. HUMIDITY CONTROL
Press the UP and DOWN buttons to select the desired relative humidity
level, the default relative humidity is 55%. When a relative humidity of
35% is selected, the compressor does not stop until the water tank is
full.
a. HUMIDITY INDICATOR button
When the appliance is switched on, the indicator light comes on
automatically. The colour of the indicator light changes according
to the humidity conditions.
RED: High humidity, RH≥70%.
ORANGE: Comfortable, 70%> RH ≥60%.
GREEN: Dry, RH<60%
It is possible to press the "Humidity indicator light" button to turn
on/off the indicator light. Note: It may take about 2 minutes after
the humidity has changed colour support for the indicator to
change colour, for example, if the humidity drops to 55%, it may
take 2 minutes for the indicator to turn green.
f.
UV LIGHT
(air purification function)
To activate the UV function, press the "UV" button and the indicator light will
illuminate. The germicidal UV light will destroy germs, bacteria and fungi, thus
improving the indoor air quality.
b.
TIMER
Press the TIMER button to set the timer. When the timer is activated, the
"TIMER" indicator lights up. Before programming the timer, make sure that the
timer function has not been activated (the indicator should be off). The following
timer programs are available. DELAY TIMER FUNCTION: When the appliance
is in standby, press the TIMER button, then use the UP and DOWN buttons to
set the number of hours you want the appliance to turn on (1~24 hours).
DELAYED POWER OFF FUNCTION: When the unit is running with the desired
settings, press the TIMER button, then use the UP and DOWN buttons to set the
number of hours you want the unit to shut down (1~24 hours).
INTELLIGENT DEFROST
The appliance defrosts automatically when the coil sensor detects
that the internal temperature is too low. During defrosting, the
indicator lights up. When the defrost cycle is complete, the unit
returns to the previous operating mode.
TANK FULL
When the water tank is full, the FULL TANK indicator light will flash
and the appliance will stop working. Once emptied and replaced, the
appliance will start working again.
optional charcoal filter (air purification function) Remove the charcoal
filter from its bag and insert it into the filter housing. It is suggested to
vacuum the charcoal filter every 2-3 weeks and change it every 3-6
months to ensure that the room remains fresh and odour free.
HUMIDITY LEVEL & TIMER 2-DIGIT DISPLAY The LED indicator performs
the following functions:
1. When the unit is switched on, it indicates the humidity level in the room.
2. When the UP and DOWN buttons are pressed, the unit indicates the desired humidity level.
3. When the timer is programmed, it will indicate the time.
Notes: When the humidity level is outside the normal operating parameters, the display will show LO/HI. If the ambient humidity is
below 20%, the message "LO" will be displayed. If the ambient humidity is above 90%, the message "HI" will be displayed.
c. d.
Buttons to adjust the
humidity level