Supero X9SCAA Скачать руководство пользователя страница 76

Страница: 76 / 87

4-16

X9SCAA Motherboard User's Manual



Intel

82574L Gigabit Network Connection

Use these features to configure the Ethernet device parameters.



NIC Configuration

Link Speed

Use this feature to change the link speed and duplex for the current port. This
feature cannot currently be changed using the BIOS.

Wake on LAN

Wake on LAN is currently not supported for the 10 Gigabit LAN.

Blink LEDs

This feature allows the user to specify the duration for LEDs to blink. The range is
from 0 ~ 15 seconds. The default setting is

PORT CONFIGURATION INFORMATION

This section displays the following port information:

•

UEFI Driver

•

Adapter PBA

•

Chip Type

•

PCI Device ID

•

PCI Bus:Device:Function

•

Link Status

•

Factory MAC Address / Alternate MAC Address

Содержание X9SCAA
























































































Результаты поиска

Содержание X9SCAA

Отзывы:

Похожие инструкции для X9SCAA

Бренды по названию

Популярные бренды

Supero X9SCAA, Руководство пользователя

Результаты поиска

Содержание X9SCAA

Отзывы:

Похожие инструкции для X9SCAA

Бренды по названию

Популярные бренды