manualshive.com logo in svg

Supero SUPERSERVER 5017C-LF, Руководство пользователя

Поделиться
Скачать
Supero SUPERSERVER 5017C-LF Скачать руководство пользователя страница 58

6-2

S

UPER

S

ERVER 5017C-LF User's Manual

6-2 Control 

Panel

The control panel (located on the front of the chassis) must be connected to the 

JF1 connector on the serverboard to provide you with system control buttons and 

status indicators. These wires have been bundled together in a ribbon cable to 

simplify the connection. 

Connect the cable from JF1 on the serverboard to the Control Panel PCB (printed 

circuit board). Make sure the red wire plugs into pin 1 on both connectors. Pull all 

excess cabling out of the airfl ow path. 

The LEDs inform you of system status. See Chapter 3 for details on the LEDs and 

the control panel buttons. Details on JF1 can be found in Chapter 5.

Figure 6-1.  Chassis Views

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When 

unpacking the board, make sure the person handling it is static protected.

Ethernet Ports

PCI Slot

Mouse/Kybrd

Power Supply

Control Panel

Dedicated IPMI LAN

COM Port

VGA Port

USB Ports

Содержание SUPERSERVER 5017C-LF





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды