Supero SUPERSERVER 5017C-LF Скачать руководство пользователя страница 37

Страница: 37 / 92

Chapter 5: Advanced Motherboard Setup

5-7

Figure 5-1. Front Control Panel Header Pins (JF1)

All JF1 wires have been bundled into single keyed ribbon cable to simplify their con-

nection. Connect one end of this cable to JF1 and the other end to the Control Panel

printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Defi nitions section in this chapter for details and pin descrip-

tions of JF1.

5-4 I/O

Ports

The I/O ports are color coded in conformance with the PC 99 specifi cation. See

Figure 5-2 below for the colors and locations of the various I/O ports.

Figure 5-2. Rear Panel I/O Ports

Backplane I/O Ports

1. Keyboard (Purple)

6. COM 1

2. PS/2 Mouse (Green)

7. VGA

3. USB Port 0

8. LAN1

4. USB Port 1

9. LAN2

5. IPMI LAN

Power Button

OH/Fan Fail LED

NIC1 LED

Reset Button

HDD LED

Power LED

Reset

PWR

Ground

NIC2 LED

Содержание SUPERSERVER 5017C-LF





























































































Результаты поиска

Содержание SUPERSERVER 5017C-LF

Отзывы:

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5017C-LF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5017C-LF

Отзывы:

Бренды по названию

Популярные бренды