Supero SUPERSERVER 5016T-TB Скачать руководство пользователя страница 55

Страница: 55 / 104

Chapter 5: Advanced Serverboard Setup

5-21

LAN1/2 Enable/Disable

Change the setting of jumper JPL1

and JPL2 to enable or disable the

LAN1 and LAN2 Ethernets ports, re-

spectively. See the table on the right

for jumper settings. The default setting

is enabled.

LAN1/2 En/Disable Jump-

er Settings (JPL1/JPL2)

Jumper Setting Defi nition

Pins 1-2

Enabled

Pins 2-3

Disabled

Watch Dog Enable/Disable

JWD controls the Watch Dog function.

Watch Dog is a system monitor that

can reboot the system when a software

application hangs. Jumping pins 1-2

will cause WD to reset the system if an

application hangs. Jumping pins 2-3

will generate a non-maskable interrupt

signal for the application that hangs.

See the table on the right for jumper

settings. Watch Dog must also be en-

abled in BIOS.

Note:

When enabled, the user needs to

write their own application software in

order to disable the Watch Dog Timer.

Watch Dog

Jumper Settings (JWD)

Jumper Setting Defi nition

Pins 1-2

Reset

Pins 2-3

NMI

Open

Disabled

USB Wake-Up

These three jumpers allow you to wake

up the system by pressing a key on the

USB keyboard or by clicking the USB

mouse of your system. The jumpers are

used together with the USB Wake-Up

feature in BIOS and both must be en-

abled to use this feature. See the table

on the right for jumper settings.

Note:

The default setting is enabled.

Please be sure to remove all other USB

devices from the USB ports whose USB

jumpers are set to disabled before the

system goes into standby mode.

USB Wake-Up

Jumper Settings (JPUSB1,

JPUSB2, JPUSB3)

Jumper Setting Defi nition

Pins 1-2

Enabled

Pins 2-3

Disabled

Note:

JPUSB1 is for USB ports #0/1, JPUSB2

is for USB2/3 and 4/5 and JPUSB3 is for

USB 6 and 7.

Содержание SUPERSERVER 5016T-TB









































































































Результаты поиска

Содержание SUPERSERVER 5016T-TB

Отзывы:

Похожие инструкции для SUPERSERVER 5016T-TB

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5016T-TB, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5016T-TB

Отзывы:

Похожие инструкции для SUPERSERVER 5016T-TB

Бренды по названию

Популярные бренды