Supero SUPERSERVER 5016T-TB Скачать руководство пользователя страница 81

Страница: 81 / 104

Chapter 7: BIOS

7-11

Intel VT-d

Select Enabled to enable Intel's Virtualization Technology support for Direct I/O VT-d

by reporting the I/O device assignments to VMM through the DMAR ACPI Tables.

This feature offers fully-protected I/O resource-sharing across the Intel platforms,

providing the user with greater reliability, security and availability in networking and

data-sharing. The settings are Enabled and

Disabled

Intel I/OAT

The Intel I/OAT (I/O Acceleration Technology) signifi cantly reduces CPU overhead

by leveraging CPU architectural improvements, freeing resources for more other

tasks. Available options are Disabled and

Enabled

Active State Power Management

Select Enabled to start Active-State Power Management for signal transactions

between L0 and L1 Links on the PCI Express Bus. This maximizes power-saving

and transaction speed. The options are Enabled and

Disabled

USB Functions

This feature allows the user to decide the number of onboard USB ports to be

enabled. The Options are: Disabled, 2 USB ports, 4 USB ports, 6 USB ports, and

8 USB ports

USB 2.0 Controller

Select Enabled to activate the onboard USB 2.0 controller. The options are

En-

abled

and Disabled.

Legacy USB Support

Select Enabled to use Legacy USB devices. If this item is set to Auto, Legacy USB

support will be automatically enabled if a legacy USB device is installed on the

motherboard, and vise versa. The settings are Disabled, Enabled and

Auto

Содержание SUPERSERVER 5016T-TB









































































































Результаты поиска

Содержание SUPERSERVER 5016T-TB

Отзывы:

Похожие инструкции для SUPERSERVER 5016T-TB

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5016T-TB, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5016T-TB

Отзывы:

Похожие инструкции для SUPERSERVER 5016T-TB

Бренды по названию

Популярные бренды