Supero SUPERSERVER 5016T-TB Скачать руководство пользователя страница 100

Страница: 100 / 104

B-2

UPER

ERVER 5016T-TB User's Manual

B-2 Installing Windows on Non-RAID Systems

Insert Microsoft's Windows XP/2003 Setup CD in the CD drive and the sys-

tem will start booting up from the CD.

Press the <F6> key when the message "Press F6 if you need to install a third

party SCSI or RAID driver" displays.

When the Windows XP/2003 Setup screen appears, press "S" to specify ad-

ditional device(s).

Insert the driver diskette you want to install into Drive A: and press the <En-

ter> key.

Press the <Enter> key to proceed with the installation process. (If you need

to specify any additional devices to be installed, do it at this time.) Once all

devices are specifi ed, press the <Enter> key to continue with the installation.

From the Windows XP/2003 Setup screen, press the <Enter> key. The

XP/2003 Setup will automatically load all device fi les and then continue with

the Windows XP/2003 installation.

After the Windows XP/2003 OS installation is complete, the system will auto-

matically reboot.

Insert the Supermicro Setup CD that came with your system into the CD drive

during system boot, and the main screen shown on page 5-26 will display.

Follow the instructions given to complete the installation.

Содержание SUPERSERVER 5016T-TB









































































































Результаты поиска

Содержание SUPERSERVER 5016T-TB

Отзывы:

Похожие инструкции для SUPERSERVER 5016T-TB

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5016T-TB, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5016T-TB

Отзывы:

Похожие инструкции для SUPERSERVER 5016T-TB

Бренды по названию

Популярные бренды