Supero Super 370DE6 Скачать руководство пользователя страница 14

Страница: 14 / 104

Chapter 1: Introduction

1-7

Introduction

370DE6 Quick Reference

Jumpers

Description

Default Setting

JA2

LVD SCSI Ch A Term.

Open (Enabled)

JA4

LVD SCSI Ch B Term.

Open (Enabled)

JA6

50pin SCSI Ch B Term

Open (Enabled)

JBT1

CMOS Clear

Pin 1-2 (Normal)

JP1

FSB Speed Setting

Pin 1-2 (Auto)

JP3

Spread Spectrum Enable

Open (Disabled)

JP55

Third P/S Fail Enable/Disable

Off (Disabled)

JP56

Speaker Enable/Disable

On (Enabled)

JP57

BIOS Select

Pin 1-2 (BIOS1)

JP58

LAN/NIC Enable/Disable

Off (Enabled)

JP60

SCSI Enable/Disable

Pin 1-2 (Enabled)

DIP Switch

Description

Default Setting

SW1 (1-4)

CPU Core/Bus Ratio

Connectors

Description

ATX POWER #1

Primary ATX Power Connector

ATX POWER #2

Secondary ATX Power Connector BANK0-

BANK1

Memory (RAM) Slots

COM1/COM2

COM1/COM2 Serial Port Connector

CPU1/CPU2

CPU 1 and CPU2 Sockets

CPU/CH/OH FAN

CPU/Overheat/Chassis Fan Headers

J13, J14

IDE Hard Disk Drive Connectors

J15

Floppy Disk Drive Connector

J16

Parallel Printer Port

J18

PS/2 Keyboard/Mouse

LAN

Ethernet Port

JA1

Ultra160 LVD SCSI CH A Connector

JA3

Ultra160 LVD SCSI CH B Connector

JF1

Front Control Panel

JP54

Third Power Supply Fail Header

PWR_SEC

Secondary ATX Power Connector

SLED1

SCSI Active LED header

USB

Universal Serial Bus Ports

WOL Wake-on-LAN Header
WOR

Wake-on-Ring Header

*Notes: Please refer to Chapter 2 for detailed information on
jumper settings and pin definitions.

Содержание Super 370DE6









































































































Результаты поиска

Содержание Super 370DE6

Отзывы:

Похожие инструкции для Super 370DE6

Бренды по названию

Популярные бренды

Supero Super 370DE6, Руководство пользователя

Результаты поиска

Содержание Super 370DE6

Отзывы:

Похожие инструкции для Super 370DE6

Бренды по названию

Популярные бренды