Supero PDSMA+ Скачать руководство пользователя страница 72

Страница: 72 / 119

4-20

PDSMA+/PDSMA-E+ User's Manual

4-7 Exit

Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys.
You should see the following display. All Exit BIOS settings are described in this
section.

Exit Saving Changes

Highlight this item and press <Enter> to save any changes you've made and to

exit the BIOS Setup utility.

Exit Discarding Changes

Highlight this item and press <Enter> to exit the BIOS Setup utility without saving

any changes you may have made.

Load Setup Defaults

Highlight this item and press <Enter> to load the default settings for all items in

the BIOS Setup. These are the safest settings to use.

Discard Changes

Highlight this item and press <Enter> to discard (cancel) any changes you've made.

You will remain in the Setup utility.

Save Changes

Highlight this item and press <Enter> to save any changes you've made. You will

remain in the Setup utility.

Содержание PDSMA+
























































































































Результаты поиска

Содержание PDSMA+

Отзывы:

Похожие инструкции для PDSMA+

Бренды по названию

Популярные бренды

Supero PDSMA+, Руководство пользователя

Результаты поиска

Содержание PDSMA+

Отзывы:

Похожие инструкции для PDSMA+

Бренды по названию

Популярные бренды