Supermicro X6DH8-G2 Скачать руководство пользователя страница 24

Страница: 24 / 104

2-4

X6DH8-G2/X6DHE-G2 User's Manual

To Un-install the Heatsink

1. Unscrew and remove the heatsink

screws from the motherboard in the

sequence as show

in the picture on

the right.

2. Hold the heatsink as show

in the

picture on the right and gently wriggle

the heatsink to loosen it from the CPU.

(Do not use excessive force when

wriggling the heatsink!!)

3. Once the CPU is loosened, remove

the heatsink from the CPU socket.

4. Clean the surface of the CPU and

the heatsink to get rid of the old

thermal grease. Reapply the proper

amount of thermal grease on the

surface before you re-install the CPU

and the heatsink.

(Caution! We do not recommend that the
CPU or the heatsink be removed. How-
ever, if you do need to un-install the
heatsink, please follow the instructions
below to uninstall the heatsink to prevent
damage done to the CPU or the CPU
socket. )

Содержание X6DH8-G2









































































































Результаты поиска

Содержание X6DH8-G2

Отзывы:

Похожие инструкции для X6DH8-G2

Бренды по названию

Популярные бренды

Supermicro X6DH8-G2, Руководство пользователя

Результаты поиска

Содержание X6DH8-G2

Отзывы:

Похожие инструкции для X6DH8-G2

Бренды по названию

Популярные бренды