Supermicro X6DH8-G2 Скачать руководство пользователя страница 18

Страница: 18 / 104

1-12

Introduction

X6DH8-G2/X6DHE-G2 User's Manual

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start

blinking to indicate that the CPU is in suspend mode. When the user presses

any key, the CPU will wake-up and the LED will automatically stop blinking

and remain on.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a

system suspend button to make the system enter a SoftOff state. The

monitor will be suspended and the hard drive will spin down. Pressing the

power button again will cause the whole system to wake-up. During the

SoftOff state, the ATX power supply provides power to keep the required

circuitry in the system alive. In case the system malfunctions and you want

to turn off the power, just press and hold the power button for 4 seconds.

This option can be set in the Power section of the BIOS Setup routine.

External Modem Ring-On

Wake-up events can be triggered by a device such as the external modem

ringing when the system is in the SoftOff state. Note that external modem

ring-on can only be used with an ATX 2.01 (or above) compliant power

supply.

Wake-On-LAN (WOL)

Wake-On-LAN is defined as the ability of a management application to re-

motely power up a computer that is powered off. Remote PC setup, up-

dates and asset tracking can occur after hours and on weekends so that

daily LAN traffic is kept to a minimum and users are not interrupted. The

motherboard has a 3-pin header (WOL) to connect to the 3-pin header on a

Network Interface Card (NIC) that has WOL capability. Wake-On-LAN must

be enabled in BIOS. Note that Wake-On-LAN can only be used with an ATX

2.01 (or above) compliant power supply.

Содержание X6DH8-G2









































































































Результаты поиска

Содержание X6DH8-G2

Отзывы:

Похожие инструкции для X6DH8-G2

Бренды по названию

Популярные бренды

Supermicro X6DH8-G2, Руководство пользователя

Результаты поиска

Содержание X6DH8-G2

Отзывы:

Похожие инструкции для X6DH8-G2

Бренды по названию

Популярные бренды