Supermicro SuperServer SYS-2049U-TR4 Скачать руководство пользователя страница 55

Страница: 55 / 151

Chapter 3: Maintenance and Component Installation

Figure 3-15. Removing/Replacing a Power Supply

Replacing the Power Supply

1. Unplug the AC power cord from the failed power supply module.

2. Press the release tab on the power supply module as illustrated.

3. Use the handle to pull the module straight out of the chassis.

4. Replace the failed module with an identical power supply module. Push the new module

into the power bay until it clicks.

5. Plug the AC power cord back into the module.

Figure 3-16. Power Supply Release Tab

Содержание SuperServer SYS-2049U-TR4
























































































































































Результаты поиска

Содержание SuperServer SYS-2049U-TR4

Отзывы:

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-2049U-TR4, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-2049U-TR4

Отзывы:

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренды по названию

Популярные бренды