Supermicro SuperServer SYS-2049U-TR4 Скачать руководство пользователя страница 50

Страница: 50 / 151

SuperServer SYS-2049U-TR4 User's Manual

Note:

Enterprise level hard disk drives are recommended for use in Supermicro chassis and

servers. For information on recommended HDDs, visit the Supermicro website at

http://www.

supermicro.com/products/nfo/files/storage/SBB-HDDCompList.pdf

Drive Carrier

Dummy Drive

Caution:

Except for short periods of time while swapping hard drives, do not operate the server

without the carriers in the drive bays.

Figure 3-10. Removing a Dummy Drive from a Carrier

Installing a Drive into the Carrier

1. Install a new drive into the carrier with the printed circuit board side facing down so that

the mounting holes in the drive align with those in the carrier.

2. Secure the hard drive into the carrier with the screws.

3. Use the open handle to replace the drive carrier into the chassis.

4. Gently close the drive carrier handle to secure the drive and carrier into the chassis

drive bay.

Содержание SuperServer SYS-2049U-TR4
























































































































































Результаты поиска

Содержание SuperServer SYS-2049U-TR4

Отзывы:

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренды по названию

Популярные бренды

Supermicro SuperServer SYS-2049U-TR4, Руководство пользователя

Результаты поиска

Содержание SuperServer SYS-2049U-TR4

Отзывы:

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренды по названию

Популярные бренды