Главная
/
Supermicro
/
SuperServer SYS-2049U-TR4
/
Руководство пользователя

Supermicro SuperServer SYS-2049U-TR4, Руководство пользователя

Поделиться

122 страниц до
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151

Страница: 137 / 151

background image

Appendix C: System Specifications

137

Appendix C

System Specifications

Processors

Quad Intel Xeon 82xx/81xx/62xx/61xx/52xx/51xx in an Socket P0-LGA3647 type socket

Note:

Please refer to the motherboard specifications pages on our website for updates to supported processors.

Chipset

Intel PCH C621 chipset

BIOS

128 Mb AMI® Flash ROM

Memory

Supports up to 12 TB of DDR4 3DS LRDIMM/LRDIMM/RDIMM ECC 2933 MHz modules in 48 SRAM slots

SATA Controller

On-chip (Intel PCH C621) controller

Drive Bays

24 2.5"" hot-swap drive bays to house SATA drives

PCI Expansion Slots

Supports up to 11 PCI-Express 3.0 expansion cards by means of four riser cards (seven external, four internal, two can be
double-width GPUs)

Motherboard

Chassis

CSE-218UTS-R1K62P; 2U Rackmount, (WxHxD) 17.2 x 3.5 x 30.7-in (437 x 89 x 780-mm)

System Cooling

Four 8-cm PWM fans

Power Supply

Model: PWS-1K62A-1R
AC Input Voltages: 100-127/200-240 VAC
Rated Input Current: 13-9A (100-127VAC)/10-8A (200-240VAC)
Rated Input Frequency: 50-60 Hz
Rated Output Power: 1600 Watt
Rated Output Voltages: 100-127VAC: +12V (83.3A), +12Vsb (2.1A); 200-240VAC: +12V (133A), +12Vsb (2.1A)

Operating Environment

Operating Temperature: 10º to 35º C (50º to 95º F)
Non-operating Temperature: -40º to 60º C (-40º to 140º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5% to 95% (non-condensing)

«
...
135
136
137
138
139
...
»

Содержание SuperServer SYS-2049U-TR4
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperServer SYS-2049U-TR4

Бренд: SafeNet Страницы: 109

totalstorage 200

Бренд: IBM Страницы: 180

OmniStor 4900F Series

Бренд: Rackable Systems Страницы: 196

Бренд: HPE Страницы: 58

WLNG-AN-DP500 Series

Бренд: Quatech Страницы: 120

totalstorage fastt100

Бренд: IBM Страницы: 160

C12C823912 - Net 2 Print Server

Бренд: Epson Страницы: 20

C823622A - Interface Type B Print Server

Бренд: Epson Страницы: 3

C12C800WN (Net 802.11b Wireless Print Server)

Бренд: Epson Страницы: 2

C32C824461 - UB R03 Print Server

Бренд: Epson Страницы: 86

Бренд: Epson Страницы: 279

C823622A - Interface Type B Print Server

Бренд: Epson Страницы: 2

ProLiant BL460c Gen8

Бренд: HP Страницы: 84

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 20

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 18

Бренд: NEC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды