Supermicro SUPERSERVER 6018R-TDTP, Руководство пользователя

Страница: 36 / 75

Chapter 5: Advanced Serverboard Setup
5-15 5-14
S
UPER
S
ERVER 6018R-TDTP/TDTPR User's Manual
NIC1/NIC2 LED Indicators
The NIC (Network Interface Controller)
LED connection for LAN port 1 is located
on pins 11 and 12 of JF1, and the LED
connection for LAN Port 2 is on pins 9
and 10. Attach the NIC LED cables here
to display network activity. Refer to the
table on the right for pin definitions.
NIC1/2 LED
Pin Definitions (JF1)
Pin# Definition
9 NIC 2 Activity LED
10 NIC 2 Link LED
11 NIC 1 Activity LED
12 NIC 1 Link LED
Power Fail LED
The Power Fail LED connection is lo-
cated on pins 5 and 6 of JF1. Refer to
the table on the right for pin definitions.
PWR Fail LED
Pin Definitions (JF1)
Pin# Definition
5 3.3V
6 PWR Supply Fail
Universal Information LED
Connect an LED cable to pins 7 and
8 of JF1 to use the Overheat/Fan Fail/
Power Fail and UID LED connections.
The red LED on pin 7 provides warnings
of overheat, fan failure or power failure.
The blue LED on pin 8 works as the front
panel UID LED indicator. The red LED
takes precedence over the blue LED by
default. Refer to the tables on the right
for pin definitions.
Universal Information LED
Pin Definitions (JF1)
Pin# Definition
7 Blue UID LED
8 OH/Fan Fail/Power Fail
OH/Fan Fail/PWR Fail
LED Status (Red LED)
State Definition
Off Normal
On Overheat
Flashing Fan Fail
Reset Button
The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a
hardware reset switch on the computer
case. Refer to the table on the right for
pin definitions.
Reset Button
Pin Definitions (JF1)
Pin# Definition
3 Reset
4 Ground
Power Button
The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off the
system. To turn off the power when the
system is in suspend mode, press the
button for four seconds or longer. Refer
to the table on the right for pin definitions.
Power Button
Pin Definitions (JF1)
Pin# Definition
1 Signal
2 Ground
Universal Serial Bus (USB)
Four Universal Serial Bus ports (USB 0/1, USB 2/3) are located on the rear I/O
panel. In addition, an internal USB header provides two front-accessible USB con-
nections (USB 4/5). One Type A connector (USB6) also supports front panel USB
connection. (Cables are not included.)
Serial Ports
Two COM connections (COM1 and COM2) are provided on the serverboard. COM1
is located on the I/O back panel. COM2, located close to Slot4 (PCI-E 3.0 x 8),
provides front access support.
10G SFP+/Ethernet LAN Ports
Two 10 Gigabit SFP+ (Small Form Factor Pluggable) Transceiver and Ethernet LAN
ports, supported by the Intel 82599SE, are located on the rear I/O panel. SFP+/
LAN ports 1/2 provide NC-SI network connections. In addition, a dedicated IPMI
LAN port, supported by the AST2400 BMC (Baseboard Management Controller),
is also located on rear I/O panel to provide LAN support for IPMI 2.0. Please refer
to the LED Indicator section for SFP+/LAN LED information.