Supermicro SUPERSERVER 1018R-WR, Руководство пользователя

Страница: 35 / 75

Chapter 5: Advanced Serverboard Setup
5-13 5-12
S
UPER
S
ERVER 1018R-WR User's Manual
N otes
•
" " indicates the location of "Pin 1".
•
Jumpers not indicated are for test purposes only.
Connector Description
COM1/COM2 COM1 (Port)/COM2 (Header)
FAN1-2, FAN4-7 System/CPU Fan Headers
J24 24-pin Main ATX Power Connector
JD1 Speaker/Buzzer
JF1 Front Panel Control Header
JIPMB1 System Management Bus Header for the IPMI Slot
JL1 Chassis Intrusion Header
JOH1 Overheat LED/Fan Fail
JPI
2
C1 Power SMB (System Management Bus)
JPWR1 8-pin CPU Power Connector
JSD1/JSD2 SATA DOM (Device On Module) Power Connector
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
JUIDB1 UID (Unit Identification) Button
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
IPMI_LAN IPMI_Dedicated LAN
I-SATA 0-3, S-SATA 0-3 (Intel PCH) SATA 3.0 Ports 0-3, S-SATA 3.0 Ports 0-3
SATA 4/5
SATA DOM (Disk On Module) Ports 4/5
SP1 Internal Speaker/Buzzer
SXB1A/SXB1B/SXB1C SMC-Proprietary WIO_L (Left) Add-On Card Slots
SXB2 SMC-Proprietary WIO_R (Right) Add-On Card Slot
T-SGPIO 1/2/3 Serial Link General Purpose I/O Headers
UID SW Unit Indentifier Switch
USB 0/1 Backpanel USB 3.0 Ports 0/1
USB 2/3 Backpanel USB 2.0 Ports 2/3
USB 4/5, 6/7, 9/10 Front Panel Accessible USB 2.0 Headers 4/5, 6/7, 9/10
USB 8 USB 3.0 Type A Header
USB 11/12 (3.0) Front Panel Accessible USB 3.0 Ports 11/12
VGA Backpanel VGA Port
LED Description State/Color Status
LE1 UID LED Blue: On Unit Identified
LEDM1 BMC Heartbeat LED Green: Blinking BMC Normal
Reset Button
The Reset Button connection is
located on pins 3 and 4 of JF1 and
attaches to the reset switch on the
computer chassis. See the table on
the right for pin definitions.
Power Button
The Power On connection is on pins
1 and 2 of JF1. These should be con-
nected to the chassis power button.
This button can also be configured to
function as a suspend button (with a
setting in the BIOS - See Chapter 7).
To turn off the power when the system
is in suspend mode, press the button
for 4 seconds or longer. See the table
on the right for pin definitions.
5-8 Connector Definitions
ATX Power 24-pin Connector
Pin Definitions
Pin# Definition Pin # Definition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
Reset Button
Pin Definitions (JF1)
Pin# Definition
3 Reset
4 Ground
Power Button
Pin Definitions (JF1)
Pin# Definition
1 Power Signal
2 Ground
Secondary Power Connector
JPWR1 must also be connected to the
power supply. See the table on the
right for pin definitions.
+12V 8-pin Power Connector
Pin Definitions
Pins Definition
1 - 4 Ground
5 - 8 +12V
Warning : To provide adequate power
supply to the serverboard, be sure to
connect all three power connectors
to the power supply. Failure to do so
will void the manufacturer warranty on
your power supply and serverboard.
Power Connectors
A 24-pin main power supply connector
(J24) and an 8-pin CPU power con-
nector (JPWR1) must be connected
to the power supply. These power
connectors meet the SSI EPS 12V
specification. See the table on the
right for pin definitions.
NC = No Connection