Supermicro SC417BE1C-R1K23JBOD Скачать руководство пользователя страница 34

Страница: 34 / 94

SC417 JBOD Chassis Manual

3-4

Overheating

A sensor on the backplane will issue a warning at 45°C. Overheating is critical at
49°C. There are several possible responses if the system overheats.

If the server overheats:

1. Use the LEDs to determine the nature of the overheating condition.

Confirm that the chassis covers are installed properly.

3. Check the routing of the cables and make sure all fans are present and operating

normally.

3-4 Drive Carrier LEDs

The chassis includes externally accessible SAS/SATA drives. Each drive carrier
displays two status LEDs on the front of the carrier.

LED Color

Blinking Pattern Behavior for Device

Activity LED

Blue

Blinking

I/O activity

Blue

Solid On

Idle SAS/NVMe drive installed

Off

Idle SATA drive

Status LED

Red

Solid On

Failure of drive with RSTe

support

Red

Blinking at 1 Hz

Rebuild drive with RSTe support

Red

Blinking with two

blinks and one stop

at 1 Hz

Hot spare for drive with RSTe

support

Red

On for five

seconds, then off

Power on for drive with RSTe

support

Red

Blinking at 4 Hz

Identify drive with RSTe support

Содержание SC417BE1C-R1K23JBOD































































































Результаты поиска

Содержание SC417BE1C-R1K23JBOD

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SC417BE1C-R1K23JBOD, Руководство пользователя

Результаты поиска

Содержание SC417BE1C-R1K23JBOD

Отзывы:

Бренды по названию

Популярные бренды