background image

Figure 17

OUTSIDE AIR KIT

 It is mandatory to install an outside air connec-

tion to the WCT6820WS wood burning fireplace. 

The following components are required and are 

included with the fireplace:

•  Outside air kit (includes 4 inch flex that goes 

up to ten (10) feet long)

•  4” Adaptor for fireplace connection

The outside air assembly must be installed ac-

cording to the following requirements:

Outside Air Installation

The outside air assembly may be installed ac-

cording to the following requirements:

A) Duct length should be kept to a minimum. 

The maximum length of a 4” interior diameter 

(100 mm) insulated flexible duct is twenty 

(20) feet (6.1 m).  (See note below).

B) The air intake register must not be installed 

more than ten (10) feet (3050 mm) above 

the base of the fireplace.

C) The fresh air must come from outside the 

house.  The air intake must not draw air from 

the attic, basement or garage.

D) The air intake should be installed where 

it is not likely to be blocked by snow or 

exposed to extreme wind and away from 

automobile exhaust fumes, gas meters and 

other vents.

E)  The duct and register may be installed above 

or below floor level.

Make a 4-1/4” (110 mm) hole in the outside 

wall of the house at the chosen location. From 

outside, place the outside air register in the hole 

(open side down) and fasten the register to the 

wall with screws as shown (see

 Figure 18)

.  

Slip the pipe into the insulated sleeve.  Place 

the insulated pipe over the register tube and 

over the fireplace’s outside air connector 

(

see 

Figure 19).

 At each end, carefully pull back the 

insulation and plastic cover exposing the flex-

ible pipe.  Using the aluminium tape provided, 

wrap the tape around the joint between the 

flexible pipe and the air inlets.  Carefully push 

the insulation and plastic cover back over the 

pipe.  Using aluminium tape, fasten the plastic 

cover in place.

NOTE:

 

We recommend not to exceed twenty 

(20) feet of 4” flexible pipe.  If you require a 

longer length we recommend that you use a 5” 

diameter flexible pipe for the complete run up 

to thirty (30) feet and a 6” diameter pipe for a 

run of up to forty (40) feet.

The duct system must be installed respecting 

the following:

1. Remove the plates closing up the 8” dia. holes 

on top of the fireplace.  Then, cut the insula-

tion in order to obtain two 8” dia. openings.  

Fix the adaptors on the fireplace openings 

by turning clockwise (

Figure 15)

.

2. Maintain at least a 2” (50 mm) clearance 

between the ducts and any combustible 

material; the required hole size is 13”  x  13” 

(330 mm x 330 mm).

  Exception #1:  For the grills, the fram-

ing can be 10-3/4” x 10-3/4” (275 mm 

x 275 mm) to provide the clearance as 

required by the integral spacers on the 

double outlet duct system.

3. The maximum number of elbows in a run 

of duct is two.

4. Maintain at least 6-1/2” (160 mm) clearance 

from the outlet grill framing to a combustible 

ceiling, side wall or mantel.

5.  When traversing a combustible wall or floor, 

a firestop must be installed at the wall or 

floor penetration.  The hole  size must  be 

13” x 13” (330 mm x 330 mm)

6.  Do not connect the hot air ducts to a central 

heating system.  Malfunction of the heating 

system’s blower will cause the fireplace to 

overheat.  A furnace duct is only single wall 

and not double wall as is required for the 

WCT6820WS fireplace hot air exhaust.  

7. Use  only  IHP  grills  and  components  as 

described in this manual. Other grills or 

registers, for example, may be too restrictive 

and may overheat the fireplace or ceiling.

8. Do not use insulated flexible ducts as they 

will overheat.

9. Do not use tees or any other components 

than the ones specifically listed here.

10. Never allow the ducting to pitch down as 

hot air will be trapped creating a fire hazard. 

 

Never route the ducting downwards.

11. The hot air outlet grills must be installed with 

the louvers pointing downwards in order to 

prevent overheating adjacent ceilings.

12. Always install the two outlet grills when 

using the double hot air outlet kit.

Rain Cap

Flashing Collar

Flashing

Firestop

68” Min.

(1727mm)

42” Min.

(1067mm)

Non-Combustible

Facing

Roof Support

Attic Radiation Shield

6-1/2” Min.

(165mm) to ceiling

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

12

Содержание WCT6820



























Отзывы: