Superior Fireplaces DRL4500 Series Скачать руководство пользователя страница 28

Страница: 28 / 50

SuperiorFireplaces.us.com

126718-01N

FIREPLACE INSTALLATION

Continued

REMOVING/REPLACING GLASS DOOR

CAUTION: Do not operate this fireplace with a

broken glass door panel or without the glass door

panel securely in place. Only doors certified with the

appliance shall be used.

CAUTION: Wear gloves and safety glasses while

handling or removing broken glass. Do not remove if

glass is hot. Keep children and pets away from glass.

WARNING: A barrier designed to reduce the risk

of burns from the hot viewing glass is provided with

this appliance and shall be installed.

WARNING: If fireplace has been running, turn off

fireplace. Let cool before removing glass doors.

Discontinue use of the appliance immediately if doors are

damaged and contact a qualified installer for repair. Only doors

certified with the appliance shall be used.

Removing Glass Door

If replacement of glass is necessary, the entire frame assembly must

be replaced. Gloves must be worn when removing/replacing glass

door. If glass is broken tape remaining glass onto frame before

removing.
1. Remove bottom access panel.
2. Unlock 3 door latches on top of firebox using your fingers or

the latch opener provided.

3. Hook opener over latch as shown in

Figure 34

. Swing the bot-

tom of the opener down toward the door. You will not need to

pull down.

4. Tilt open glass door 45° from the top of firebox and lift up to release

door from retaining channel

(see

Figure 35

Figure 34 - Latch Opener

Figure 35 - Removing/Replace Glass Door

Glass Door

Door Latches

Replacing Glass Door

1. Position door frame in front of firebox opening tilting top of door

about 45° toward you. Insert bottom flange of glass door into the

retaining channel at the bottom of firebox

(see

Figure 35

Make

sure door is center with firebox opening.

2. Tilt top of door up toward top of firebox.
3. Secure 3 top door latches.

NOTE: It is important to ensure proper log placement per the manual

when installing these units. Verify pilot flame is not obstructed.

See "Burner And Pilot Flame Appearance And Sooting" on Page 35.

WARNING: Do not change or substitute glass

pebbles provided with this fireplace. If replacing, use

only replacement glass pebbles. See Parts,

Page 44

WARNING: Do not block pilot ports with embers.

WARNING: Do not block pilot ports with glass

pebbles.

WARNING: Do not place the glass pebbles on the

burner, only on the burner tray as illustrated in

Figure

36, Page 29

Figure 33 - Installing Rear Panel for One Sided Regular

Applications

For one sided regular application,

finish installing rear panel by

securing with 19 self tapping

screws included with fireplace.

GLOWING EMBERS AND GLASS PEBBLE INSTALLATION

Содержание DRL4500 Series



















































Результаты поиска

Содержание DRL4500 Series

Отзывы:

Похожие инструкции для DRL4500 Series

Бренды по названию

Популярные бренды

Superior Fireplaces DRL4500 Series, Инструкции по сборке, установке и эксплуатации

Результаты поиска

Содержание DRL4500 Series

Отзывы:

Похожие инструкции для DRL4500 Series

Бренды по названию

Популярные бренды