Superior Fireplaces DRL4500 Series Скачать руководство пользователя страница 26

Страница: 26 / 50

SuperiorFireplaces.us.com

126718-01N

FIREPLACE INSTALLATION

Continued

Figure 27 - External Regulator with Vent Pointing Down

(Propane/LP Only)

Check your building codes for any special requirements for locating

equipment shutoff valve to fireplaces.
Apply pipe joint sealant lightly to male NPT threads. This will prevent

excess sealant from going into pipe. Excess sealant in pipe could

result in clogged fireplace valves.

Figure 28 - Gas Connection

Equipment Shutoff Valve

with 1/8" NPT Tap*

3" (77 mm)

Minimum

Approved

Flexible Gas

Line

Cap Pipe Tee

Joint Nipple

Sediment Trap/Drip

Leg

Natural

- From Gas

Meter (5.5" W.C. to

10.5" W.C. Pressure)

Propane/LP

From

External Regulator

(11" W.C. to 14" W.C.

Pressure)

* The equipment shutoff valve may be supplied with the

appliance or you can purchase it from your retailer.

Propane/LP

Supply Tank

External Regulator with

Vent Pointing Down

WARNING: Use pipe joint sealant that is resistant

to liquid petroleum (LP) gas.

We recommend that you install a sediment trap/drip leg in supply

line as shown in

Figure 28

. Locate sediment trap/drip leg where it is

within reach for cleaning. Install in piping system between fuel supply

and fireplace. Locate sediment trap/drip leg where trapped matter is

not likely to freeze. A sediment trap traps moisture and contaminants.

This keeps them from going into fireplace gas controls. If sediment

trap/drip leg is not installed or is installed wrong, fireplace may not

run properly.

CONNECTING FIREPLACE TO GAS SUPPLY
Installation Items Needed

•  5/16" hex socket wrench or nut-driver
•  Sealant (resistant to propane/LP gas, not provided)
1.  Route flexible gas line (provided by installer) from equipment

shutoff valve to fireplace. Route flexible gas supply line through

one of the access holes on side of fireplace.

2. Attach flexible gas line from gas supply to control valve

(see

Figure

3. Check all gas connections for leaks. See Checking Gas Connec-

tions,

Page 27

Figure 29 - Connecting Incoming Gas Line to Flex Gas Line

NOTE:

1) Wire connections not shown for clarity

2) * 1/8" NPT Plugged Tapping

MAIN

OUT

PILOT

ADJ

PILOT

Pilot Adjustment

Inlet Pressure Tap

Outlet Pressure Tap

Gas Shutoff Valve

Flexible Gas Line

Do NOT Kink

1/2" NPT

Incoming Gas

Line

Set Screw

Содержание DRL4500 Series



















































Результаты поиска

Содержание DRL4500 Series

Отзывы:

Похожие инструкции для DRL4500 Series

Бренды по названию

Популярные бренды

Superior Fireplaces DRL4500 Series, Инструкции по сборке, установке и эксплуатации

Результаты поиска

Содержание DRL4500 Series

Отзывы:

Похожие инструкции для DRL4500 Series

Бренды по названию

Популярные бренды