manualshive.com logo in svg

SunStar STARGLO Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
SunStar STARGLO Series Скачать руководство пользователя страница 15

Form #43219020 
June 09 

14

 

16)  OPTIONAL PARABOLIC REFLECTOR EXTENSION ASSEMBLY 

 

The heater is completely factory assembled and requires no field assembly.  If the optional parabolic reflector 
extension is utilized, locate and identify the end panels 
and side panels as shown in the following diagram.  
Attach the side panels as shown.  Attach the end panels 
so that the end flanges of the end panels overlap the side 
panels.  Attach the side panels and end panels together 
with the screws provided in the kit.  Attach the remaining 
screws as shown in Detail A.  This is to ensure that the 
Parabolic Reflector Extension is securely attached to the 
reflector.  The clearances to combustibles (shown on the 
clearance label that is secured to the reflector on the 
control end of the heater and in Section 4 of these 
instructions) must be closely observed.  

Please order the 

Parabolic Reflector Extension Kit using the Part Numbers 
below: 

 

Model No. 

Parabolic Reflector 

Extension Kit Number 

SG3, SG4 

#43822010 

SG6, SG8 

#43822020 

SG10, SG12 

#43822030 

SG13, SG14, SG15 

#43822040 

 
 
 

17)  OPTIONAL PROTECTIVE REVERB SCREEN 

 

The optional protective Reverb Screen acts as a safety net in 
the unlikely event that the ceramic tile assembly is broken by 
an outside force.  In addition, it increases the overall 
emissivity of the radiating surface with a blackbody radiation 
effect.  It is recommended in high-traffic areas as well as 
where improved radiant output is desired.  

Please order the 

Protective Reverb Screen using the Part Numbers listed to 
the right: 

 
 

18) REPLACING 

PARTS 

 

At all times when parts are being replaced, ensure that both the gas and electrical supplies are disconnected.  
Various parts are available from the factory for replacement by a licensed service person.  Refer to the exploded 
parts guide in Section 20 for all replacement parts. 

 
 

19) INSTALLATION 

DATA 

 

Date of  
Installation:  

Number of 
Heaters in System: 

 

Heater Serial Number: 

 

Heater Model: 

  SG

 

 

 

 

N =Natural  Gas 

L =Propane Gas

 

 
 

Model No. 

Reverb Screen 

Kit Number 

SG3, SG4 

#43876010 

SG6, SG8 

#43876020 

SG10, SG12 

#43876030 

SG13, SG14, SG15 

#43876040 

Sheet Metal

Screw

DETAIL A

(Section View)

Parabolic Reflector Extension

(END PANEL)

Parabolic Reflector Extension

(SIDE PANEL)

Содержание STARGLO Series


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды