SunStar KM-957 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

SunStar KM-957 Series Скачать руководство пользователя страница 10

10

2

Installation

Warning

▶

Installation of the machine should be performed by a trained engineer.

▶

Any electrical wiring must be performed by a qualified technician or agent.

▶

The machine weighs over 54kg. At least 2 persons should carry out the installing work.

▶

Plug in after the installation is complete. If the operator mistakenly steps down on the pedal

with the pug in, the machine will start automatically and can cause physical injuries.

▶

Connect the ground (earth) wire. An unstable connection may result in an electric shock or a

malfunction.

▶

Place the belt cover on top of the machine.

▶

Use both hands when bending the machine backwards or returning it to the normal position.

Using only one hand can lead to severe hand injuries due to the weight of the machine.

1) Installation of machine head

Insert the machine head hinge

①

into the bed holes. After aligning it with the rubber hinge

②

, stand the machine on the

rubber cushion

③

that is in the direction of the user.

[Figure 1]

[Figure 2]

2) Installation of oil tray (oil fan)

Move the twice inclined side of the oil fan

①

so that it faces the user and use 6 nails to fix it to the bottom of the table

②

.

«
...
8
9
10
11
12
...
»

Содержание KM-957 Series

































Отзывы:

Нет отзывов