SunStar KM-757 Скачать руководство пользователя страница 28

Страница: 28 / 35

B. Adjusting movable and fixed knife (See Figure 49.)

a) Like in Figure 49, adjust the position of the fixed knife

③

so that the fixed knife right side edge

②

matches the

movable knife inner side edge

①

b) The initial assembling position of the movable knife

④

is where the movable knife-edge protrudes about 3 mm

from the edge of the fixed blade. Please check the

“

final fixing of the movable knife initial position

”

on page 29.

c) The surface adhesion conditions

⑤

of fixed blade edge and movable knife upper side have huge impact on its

trimming capacity. Please note the various cases of movable/fixed knife surface adhesion conditions on the picture.

[Correcting the adhesive conditions of movable and fixed knives]

Like in Figure 49, operate manual trimming movement with color ink on the movable knife-edge. By checking

the ink trace remaining on the movable knife, the surface adhesion condition of the movable/fixed knives can be

tested.

If the surface adhesion is not very good (same method is used to adjust the tension of movable/fixed knives),

please use the following methods: adjusting the amount and position of the washer

⑦

in the lower side of the

movable knife base

⑥

, horizontally adjusting the assembling position of movable knife shaft collar

⑧

, and

correcting the shape of fixed blade

⑨

setting position.

[Checking the surface adhesion]

※

Apply color ink on the upper
side of the movable knife-edge

(good)

(bad)

[Figure 49]

Содержание KM-757




































Результаты поиска

Содержание KM-757

Отзывы:

Похожие инструкции для KM-757

Бренды по названию

Популярные бренды

SunStar KM-757, Руководство пользователя

Результаты поиска

Содержание KM-757

Отзывы:

Похожие инструкции для KM-757

Бренды по названию

Популярные бренды