SunStar KM-757 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

SunStar KM-757 Скачать руководство пользователя страница 18

18

6) Routing the upper thread

Place the thread take-up lever to the highest position and hang the upper thread like in Figure 25. The adequate length of

upper thread extending from the needle hole is 50mm for initial sewing.

[Figure 25]

[Figure 24]

5) Inserting the bobbin

Stop the needle

①

at the highest position. Following the Figure 24, insert the bobbin (where the thread is rolled onto) or the

bobbin case

②

into the hook

③

. After laying down the bobbin holder

④

, close the slide plates

⑤

on the right and left.

Caution

▶

Turn off the power switch when routing the upper thread. If the operator mistakenly presses
down on the pedal while switched on, the machine will start automatically and can cause
physical injuries.

▶

When using the clutch motor, be aware that the motor will continue to rotate for a while after
the power is switched off. Start to work on the sewing machine only after the motor has come
to a complete stop.

«
...
16
17
18
19
20
...
»

Содержание KM-757




































Отзывы:

Нет отзывов