Sunshine Solar Evacuated Tube Solar Water Heater Скачать руководство пользователя страница 6

 

 

 Copyright 2013 

0800 sunshine  |  

[email protected]

  |  www.sunshinesolar.co.nz |

 6

 

 

 

Section 2: 

General guidelines for roof-mounting of the solar collectors. 

  

 

The ideal location for the Solar Collectors is on a roof facing the mid-day / early afternoon sun.  (North / NNW 

in New Zealand). 

 

The panel angle to the sun should be approximately the same as the geographical latitude (e.g. 36° for Auckland, 

45° for Dunedin). 

 

If  the  roof  pitch  is  significantly  less  than  this  value,  we  recommend  that  the  panel  is  elevated  on  a  frame  to 
maximise the collector efficiency. 

 

Clients will have a view on the use of a frame; it is important to explain to them (in writing) that Sunshine Solar 

does  recommend  a  frame  in  these  circumstances  to  maximise  efficiency,  especially  in  higher  value  latitudes  
(eg Dunedin). 

 

It is important also that the panels will not be shaded for any of the day in summer or winter by trees or buildings etc.  

Pitch roof – elevated  

Pitch roof – flat to roof  

Flat roof – elevated 

 

 

Stainless steel fittings of an appropriate grade must be used, including roof mounting screws. 

 

Roof  cladding  penetrations  must  be  appropriately  sealed  according  to  local  building  code  standards  and  must 
follow good practice at all times. 

 

 

Содержание Evacuated Tube Solar Water Heater


















Отзывы: