background image

119832 Rev. G

17

Q UI C KI E   PU LS E

VIII. USE AND MAINTENANCE

1.   Airing up your tire: 

a.

CAUTION–

To prevent tire damage: 

• Use a hand pump (or a low volume air pump) 

to inflate tires.  Use a tire gauge to check pressure.

b. Remove the air stem cap.
c. Inflate the tire to the proper pressure level (listed on the

tire sidewall)

E.  MOTOR BRUSHES 

Check the motor brushes every four (4) months for wear.  The
brushes should be clean and shiny.  Replace worn or blackened
brushes

F.  DISPOSING OF BATTERIES

WARNING

1. All batteries, once they have reached the end of their useful

life are deemed to be hazardous waste.

2. For further information on handling and recycling contact

your local recycling authority.

3. Always dispose of product through a recognized agent.

G. ORDERING PARTS 

When you order parts, provide the following: 

1. Model of chair
2. Serial number of chair
3. Left hand or right hand control
4. Part number, description and quantity of parts you need.
5. State reason for replacement.

H. SAFETY CHECKLIST

You should check the items on this chart at the indicated intervals.
If any of the items are loose, worn, bent or distorted, immediately
have them checked and/or repaired by your Authorized Dealer.
Frequent maintenance and servicing will improve performance,
extend wheelchair life, and help prevent injuries.

WARNING

The owner and/or Caregiver for the use of this product, is responsible for
making sure that it has been setup and adjusted by a trained service profes-
sional under the advice of a healthcare advisor.   The chair may require
periodic maintenance or certain in-use adjustments that may be performed
by the owner or caregiver.

A. INTRODUCTION 

WARNING

1. Your chair needs regular maintenance for peak performance

and to avoid injury from chair failure, damage or premature
wear.

2. Inspect and maintain this chair  per the “Safety Checklist”. 
3. If you detect a problem, make sure to service or repair the

chair before use.

4. At least once a year, have a complete safety check and service

of your chair performed by a supplier.

B. CLEANING 

1.   Paint Finish: 

Clean the paint finish with mild soapy water monthly. 

Protect the paint with a coat of non-abrasive auto wax every
three months. 

2.   Motors: 

Clean around motor area weekly with a slightly damp (not
wet) cloth. 

Wipe off or blow away any fluff, dust, or dirt on or around
the motors. 

NOTE

– You do not need to grease or oil the chair. 

3.   Upholstery: 

Hand-wash only as needed. Machine washing may damage
fabric. 

Drip-dry only. Heat from a dryer may damage fabric. 

NOTE–

Washing the fabric may decrease fire retardant properties. 

4.   Joystick: 

Use a cloth that has been slightly dampened with diluted
detergent. to clean the joystick and boot.

LCD Screen can be cleaned with a soft, lint free, dry cloth.

NOTE –

NEVER use any type of window cleaner, scouring powder, or any

cleanser with solvents such as alcohol, benzene, ammonia, or
paint thinner.  Never use abrasive pads or paper towels.

C. STORAGE TIPS 

1. Store your chair in a clean, dry area. If you fail to do so, parts

may rust or corrode. 

2. Before using your chair, make sure it is in proper working

order. Inspect and service all items on the “Safety Checklist”.

3. If you store this chair for more than three months, have it

inspected by a supplier before use.

4. Use petroleum jelly to re-grease the terminals after connect-

ing cable to battery. (Completely cover the terminal nut and
bolt, cable clip and any exposed cable with jelly). 

D. TIRE PRESSURE

WARNING

1. Check for signs of wear and correct air pressure in pneu-

matic tires weekly. 

2. For best performance, inflate tires to the same pressure

level, as shown on the tire sidewall: 
• 14" pneumatic drive wheels– 35 to 45 psi (240 to 310 Kpa)

D

ai

ly

W

e

e

k

ly

M

o

n

th

ly

Q

u

ar

te

rl

y

A

n

n

u

al

ly

  Charge Batteries                                     

R

                                   

  Check tires for proper inflation level                 

R

                          

  Check plugs and connectors for 

proper connections                                                    

R

                

  Check all moving parts for wear                                          

R

        

  Inspect all nuts, bolts and fasteners 

for looseness or wear                                                         

R

        

  Inspect upholstery for wear                                                 

R

        

  Service by Authorized Supplier                                                      

R

SAFETY & FUNCTION CHECK

Содержание Pulse 5BC













































Отзывы: