background image

18 

 

MAINTENANCE & CARE 

General cleaning will help prolong the life and performance of your treadmill. Keep the unit clean and 
maintained by dusting the components on a regular basis. Clean both sides of the 

Running Belt (No. 

C19) 

to prevent dust from accumulating underneath. Keep your running shoes clean so that dirt from 

your shoes does not wear out the 

Running Board (No. D13)

 and 

Running Belt (No. C19)

. Clean the 

surface of the 

Running Belt (No. C19)

 with a clean, damp cloth.

 

 
To better maintain the treadmill and prolong its life, it is suggested that the treadmill be powered off 
for 10 minutes every 2 hours and fully powered off whenever not in use. 
 
A loose 

Running Belt (No. C19)

 will result in the runner sliding off when running, while too tight of a 

Running Belt (No. C19)

 will negatively affect the motor

’s performance and also create more friction 

between the roller and 

Running Belt (No. C19)

. The most suitable tightness for the 

Running Belt 

(No. C19)

 is pulled out 

50-75mm

 from the 

Running Board (No. D13)

.   

 

CENTERING THE RUNNING BELT: 

Place the treadmill on level ground and set it at 4-5MPH to check if the 

Running Belt (No. C19) 

drifts. 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
 
 
 
 
 

 

 
 

 

 

If  the 

Running  Belt  (No.  C19) 

moves  to 

the right, turn the adjusting bolt on the right 
side 

¼

  turn 

clockwise

,  then  turn  the  left 

adjustment  bolt  ¼  turn 

counter-clockwise

If  the 

Running  Belt  (No.  C19) 

does  not 

move,  repeat  this  step  until  it  centers. 
Refer to Figure A. 

If  the 

Running  Belt  (No.  C19) 

moves  to 

the left, turn the adjusting bolts on the left 
side 

¼ 

clockwise

,  then  turn  the  right 

adjustment bolt ¼ turn 

counterclockwise

. If 

the 

Running  Belt  (No.  C19) 

does  not 

move,  repeat  this  step  until  it  centers.   
Refer to Figure B.

 

Over  time,  the 

Running  Belt  (No.  C19) 

will  loosen.  To  tighten  the 

Running  Belt 

(No.  C19)

,  turn  the 

Left  &  Right 

side 

adjustment  bolts  one  full  turn 

clockwise

Check  the  tension  of  the 

Running  Belt 

(No.  C19)

.  Continue  this  process  until 

Running Belt (No. C19) 

is at the correct 

tension.  Make  sure  to  adjust  both  sides 
equally  to  ensure  correct  belt  alignment. 
Refer to Figure C. 

Содержание SF-T7857



























Отзывы: