background image

19 

 

LUBRICATING THE TREADMILL 

 
IMPORTANT NOTE: 

You will need to lubricate your treadmill before the first use. 
 
 

RUNNING BELTS & TREADMILL LUBRICANT: 

Lubricating  the 

Running  Board  (No.  D13) 

and 

Running  Belt  (No.  C19)

  is  essential  as  the  friction 

between the two affects the life span and function of the treadmill. It is suggested that the 

Running 

Board (No. D13) 

and 

Running Belt (No. C19) 

be inspected regularly. Should you find any wear on 

the 

Running Board (No. D13)

, please contact us at:[email protected]

 

WARNING:

 Always unplug the treadmill from the electrical outlet before cleaning, lubricating or 

repairing the unit.   
 
 

HOW TO LUBRICATE: 

1. Raise the 

Running Belt (No. C19) 

up on one side and apply lubricant to the 

Running Board (No. 

D13)

. Use a rag to thoroughly wipe the lubricant over the 

Running Board (No. D13)

. Repeat this 

process for the other side. 

2. The moving parts should turn freely and quietly. Abnormal moving parts will affect the safety of the 

equipment. Inspect and tighten bolts regularly. 

3. To better maintain the treadmill and prolong its lifespan, it is suggested that maintenance be done 

on a regular basis. 

4. A loose 

Running Belt (No. C19) 

will result in the runner sliding off during use, while too tight of a 

Running Belt (No. C19) 

will negatively affect the motor

’s performance and also create more friction 

between the roller and 

Running Belt (No. C19)

. The most suitable tightness for the 

Running Belt 

(No. C19) 

is pulled out 

50-75mm

 from the 

Running Board (No. D13)

 

 

 

 
 

The following time table is recommended: 

Light user (less than 3 hours/ week)       

every six months

 

Medium user (3-5 hours/ week)               

every three months

 

Heavy user (more than 5 hours/ week)   

every two months

 

 

Содержание SF-T7857



























Отзывы: