background image

6614A 

REV. A

 

rev. 9/11/19

2.  The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to all zerk  

 

grease fittings, caster wheels, front axle wheels, elevator arm, handle base pivot bolts, release mechanism and all other bearing surfaces.

IMPORTANT: 

Any jack found to be defective as a result of worn parts due to lack of lubrication or air/hydraulic system contaminated with water, rust 

and/or foreign materials from the air supply or other outside source is not eligible for warranty consideration.

3.  It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. An external leak requires immediate  

 

repair which must be performed in a dirt-free environment by an authorized service center.

IMPORTANT:

 In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake fluid or transmission oil in the jack.

4.  Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of the jack but 

not any moving hydraulic components.

5.  Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks hydraulic fluid. 

Do not use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective action before using the jack 
again.

6.  Any hydraulic repairs within the warranty period must be performed by an authorized service center.

TROUBLESHOOTING

SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY’S SUNEX TOOLS

®

 BRANDED 

PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS. 

Sunex International, Inc. will repair or replace its Sunex Tools

®

 branded products which fail to give satisfactory service due to defective 

workmanship or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific 
product. This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will repair or replace at our option any part  
or unit which proves to be defective in material or workmanship.

Other important warranty information

This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs 
or replacement made by anyone other than Sunex Tools

®

 or its authorized warranty service centers. The foregoing obligation is Sunex Tools’ 

sole liability under this or any implied warranty and under no circumstances shall we be liable for any incidental or consequential damages.

NOTE:

 

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may 

not apply to you. Return equipment or parts to an authorized service center, transportation prepaid. Be certain to include your name and 
address, evidence of the purchase date, and description of the suspected defect. If you have any questions about warranty service, please 
write to Sunex Tools

®

. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 

Repair kits and replacement parts are available for many of Sunex Tools products regardless of whether or not the product is still covered by 
a warranty plan.

SHIPPING ADDRESS:

 Sunex Tools  •  315 Hawkins Rd.  •  Travelers Rest, SC 29690

MAILING ADDRESS: 

Sunex Tools  •  P.O. Box 1233  •  Travelers Rest, SC 29690

LIMITED WARRANTY

PROBLEM

ACTION

1. Unit will not lift rated load.

Purge air from hydraulic system by following procedure under SETUP.

2. Unit will not sustain rated load or feels “spongy” under rated load.

Purge air from hydraulic system as above.

3. Unit will not lift to full height.

Purge air from hydraulic system as above.

4. Handle tends to raise up while the unit is under rated load.

Pump the handle rapidly several times to push oil past ball valves in 
power unit.

5. Unit still does not operate.

For a complete list of authorized 

hydraulic

 repair centers please visit 

www.toolwarrantyrepair.com.

Содержание 6614A

















Отзывы: