Sunbeam STEAM MASTER 4049, Инструкция по эксплуатации

Страница: 5 / 28

◆
5
S
TEAM
E
XTRA
S
TEAM
S
TEAM
U
LTRA
CLEAN
S
T
E
A
M
DRY
F
D
B
C
I
J
K
L
M
A
E
G
H
FEATURES
A. Variable Steam Dial
— Adjusts steam level for different ironing needs. For dry ironing.
turn dial to DRY. For steam ironing, turn dial to the . For additional steam, turn dial to the
or . (Refer to Ironing Guide for recommended settings).
B. Steam Valve
(connected to the variable steam dial)
— Removable to prevent scale build up.
C. Steam Indicator Mark
D. Auto-Off Indicator (Some Models Only)
E. Temperature Dial
— Controls heat output of iron. Adjust dial according to ironing needs.
For low temperatures, turn dial to first dot. For medium temperatures, turn dial to second
set of dots. For high temperatures, turn dial to third set of dots.
(Refer to Ironing Guide for
recommended settings).
F. Winding Button — Retracts cord with a push of the button. (Refer to Using the
Retractable Cord)
G. Temperature Indicator Mark
H. Cord Reel
— Provides convenient cord storage. Allows for use of only the amount of cord
needed, eliminating extra cord that gets in the way. Push button to automatically retract cord.
I. Soleplate — Has full length button grooves for added convenience when ironing shirts and
blouses; some models have non-stick coating.
J. Sliding Water Reservoir Cover — Prevents dust and foreign matter from entering the
water tank; resists water splashing during ironing.
K. SPRAY MIST
®
Feature (Some Models Only)
L. SPRAY MIST
®
Button
— Provides a fine spray mist for spot dampening.
(Some Models Only)
M. SHOT OF STEAM
®
Button
— Provides a powerful burst of steam for maximum steam
power. On select models, can also be used while holding the iron vertically to remove
wrinkles from hung garments or drapes.
• MOTION SMART
®
Auto off
(Some Models Only)
— Shuts off if iron is unmoved for
15 minutes in the upright position, or 30 seconds in the ironing position.
◆
6
USING THE RETRACTABLE CORD
1.
When winding the cord, hold the plug with one hand, and press the
winding buttonwith the other hand.
(Failure to hold plug may cause plug to fly).
2. The cord reel is compact for multi-layer winding of the cord. In case cord is not fully rewound,
pull out the cord and steer cord evenly on the reel.
3. In case the cord is not pulled out easily, pull cord firmly.
4. Select the amount of cord desired before plugging into an electrical outlet.
5. Do not allow children to use retractable cord feature as the cord may cause injury.
BEFORE THE FIRST USE
• When turned on for the first time, your new iron may give off a slight odor for up to ten
minutes. This is due to the initial heating of the materials used. It is safe, not detrimental to the
performance of the product, and will not recur.
• Prior to first use, clean steam vents using the SHOT OF STEAM‚ feature. After cleaning vents,
run iron over an all-cotton cloth to remove any residue.
• When not ironing, always have steam dial turned to DRY (See Diagram).
INSTRUCTIONS FOR USE
Dry Ironing
• Plug the cord into a 120 volt AC outlet. On units with
automatic shut off, the auto off light will illuminate.
• Turn the temperature dial to the desired setting (refer to
Ironing Guide for recommended settings). While iron is
heating, place iron on heel rest on a stable, protected surface.
• Set the steam dial on DRY to prevent steam flow if water is in the tank.
Steam Ironing
• Make sure the plug is removed from the wall socket before filling the iron with water.
• Turn the the steam dial to DRY.
• Place the iron on its heel and open the water reservoir cover. Pour water slowly into the water
reservoir. Fill up to the maximum water level. To prevent the risk of burns, use caution
when filling a hot iron with water. Burns can occur from touching hot metal
parts, hot water or steam.
Push firmly to close the cover. NOTE: Tap water may be used
due to the special design of this iron. However, in areas with very hard water, distilled or
demineralized water is recommended.
• Turn the temperature dial to any of the temperatures within the steam band and allow the iron
to heat for approximately 2 minutes before ironing. While heating, place iron on heel rest on
a stable, protected surface.
• Turn steam dial to for regular steam, or to for extra steam or
for ultra steam. NOTE: When using extra or ultra steam, it may be necessary to fill the tank
more often.