FIG. 4
FIG. 5
SAVE THESE INSTRUCTIONS
Before installation, make sure the surface you intend to mount the product on is free of moisture, oil, grease, dust
and dirt to ensure proper adhesion. Test painted surfaces. Adhesive tape may damage surface when removing.
There are 2 ways to operate the units.
A. Stand-alone unit:
Set the timer switch to the desired
light duration
(FIG. 1)
. Insert 3 batteries in each unit
(FIG. 2)
.
Press the On / Off button once, the light will turn on
(FIG. 3)
.
If there is sufficient ambient light or no motion is detected,
the light will turn off when the preset time has elapsed.
B. Linked with other unit(s):
Set the timer switch to the
desired light duration
(FIG. 1)
. Press the On / Off button
twice
(FIG. 4)
. The linking indicator light will turn on and
flash, indicating the unit(s) are linked
(FIG. 5)
. Repeat for all
other units. Linked units will turn on when one of the units
detects motion in low ambient light.
To unlink a unit, press the On / Off button once. The linking
indicator light will turn off.
SETUP
SETUP AND INSTALLATION
FIG. 8
FIG. 11
FIG. 6
FIG. 7
FIG. 1
There are 3 ways to mount the unit.
A. Double-sided foam adhesive tape:
Mark the desired area where you want to install. Remove
one side of the tape and secure to the back of the LED light.
Then remove the other side of the tape and secure to where
you want to install
(FIG. 6)
.
B. Drywall surface mounting anchor screw:
Place the mounting plate over the desired mounting location
and mark the center of the holes to be drilled. Drill two
pilot holes 0.45 - 0.50 cm / 0.18 - 0.20 in diameter into the
surface. Insert the anchors. Place the mounting plate over
the holes and screw in the mounting screws 2 cm / 0.79 in
to secure
(FIG. 7)
.
C. Wood surface mounting screw:
Place the mounting plate over the desired mounting location
and mark the center of the holes to be drilled. Then place
the mounting plate over the marks and screw in the
mounting screws 1.2 cm / 0.47 in to secure
(FIG. 8)
.
INSTALLATION
All units within the package are already paired at the time
of purchase.
NOTE: To prevent damage to the wall,
use adhesive glue remover.
Follow the manufacturer’s instructions.
NOTE: A unit in a room with sufficient
ambient light will not illuminate.
FIG. 3
PAIRING ADDITIONAL UNITS
FIG. 2
FIG. 12
If you have purchased more than one pack and
want to link more than 3 units, please follow pairing
instructions below.
NOTE: Pairing time limit (3 minutes):
the linking indicator light of the
master unit will turn off after 3 minutes.
After 3 minutes, you will need to re-start
the entire pairing procedure.
FIG. 9
FIG. 10
For troubleshooting tips or to
download this instruction manual,
please visit the product page on our website:
www.limagehomeproducts.com
NOTE: Linkable up to 10 units,
maximum 8 m / 26.2 ft between 2 units.
STEP 1
Pairing new units with the master unit:
Insert all 3 batteries into the unit to be paired. Press and
hold the On / Off button
(FIG. 11)
. The unit light will flash 2
times within 3 seconds. Pairing is now complete
(FIG. 12)
.
Release the On / Off button.
Repeat (STEP 2) for the next units to be paired.
Designate one of the units as your master unit:
First, insert 2 batteries
(FIG. 9)
. When inserting the 3rd
battery, press and hold the On / Off button
(FIG. 10)
. The red
linking indicator light will flash, indicating the unit is ready
to be paired
(FIG. 12)
.
STEP 2
back
