background image

PG 14

www.summitstands.com

WARNING

!

ALL STRAPS MUST BE 100% INSPECTED INCLUDING 
ALL LADDER SECTIONS TO ENSURE THEY ARE 
SECURED BY MEANS OF BOLTS OR PINS PRIOR TO 
EACH USE. 

Never jump or bounce on any 
other part of the treestand 
in an attempt to force the 
platform to seat into the tree.

WARNING

!

WARNING

!

You 

MUST

 now put on your safety harness if you have 

not already done so.  

ALWAYS

 refer to your harness 

instructions included with this stand for proper use of 
your safety harness.

WARNING

!

YOU WILL NOT

 be connected to a safety rope / strap 

while you climb into or out of this treestand.  

USE 

EXTREME CAUTION

 while ascending or descending 

the ladder.  TAKE YOUR TIME and do not hurry.

WARNING

!

This ladder 

MUST

 be held in place while it is ratcheted 

tight and while the top ratchet is put into place.  Do 
not use until all straps are securely attached.

12. 

Now, put on a Full Body Fall Arrest Harness System so you can attach the ladder platform to the tree. 

See FBFAHS 

instructions and warnings for proper use. 

With one person on each side of the ladder section holding the ladder stand in place, 

carefully climb up the ladder stand (using 3 points of contact as you climb and with your FBFAHS already on.)

13. 

Upon arrival to the foot platform area, attach your Tether Strap to the tree and ensure you are secured properly to the tree 

in the event that a fall might occur. Next, keeping your weight centered on the middle of the platform area, wrap the previously 
installed upper ratchet strap end around the tree and pull it through the barrel of the previously installed upper ratchet strap on 
the other side.  Pull the strap tight and ratchet tight against the tree. 

Use figure 43 for proper ratchet strap threading.

14.  

Wrap the previously installed lower ratchet strap end around the tree and pull it through the barrel of the previously 

installed lower ratchet strap on the other side.  Pull the strap tight and ratchet tight against the tree. 

Use figure 43 for proper 

ratchet strap threading.

IMPORTANT: ALL RATCHET STRAPS MUST BE RATCHETED AROUND THE BARREL AT LEAST TWICE!!

15.

 While at foot platform area, inspect all parts and bolts for any damage that may have been caused during set-up or when 

carrying the product into the field. If any damage or loose hardware is found, discontinue use immediately. ALL REPAIRS MUST 
BE DONE AT GROUND LEVEL!! 

16.

  When descending the treestand, detach your Tether Strap and carefully climb down the ladder.  Always use 3-points of 

contact as you descend.  Re-check the Criss-Cross straps to ensure they are still tight.  Re-tighten if needed.  

Содержание The Vine Double Hunter

































Отзывы: