background image

2

1. SAFETY WARNING!

Do not operate the dryer until the operating instructions for the particular control system and this manual have
been read and understood by all personnel concerned.

It is essential that personnel employ safe working practices and observe all related regulations and legal requirements for
safety when operating the dryer.

When handling, operating or carrying out maintenance on the dryer, personnel must employ safe engineering practices
and observe all relevant local health and safety requirements and regulations. The attention of UK users is drawn to the
Health and Safety at Work Act 1974, and the Institute of Electrical Engineers Regulations.

Most accidents which occur during the operation and maintenance of machinery are the result of failure to observe basic
safety rules or precautions. An accident can often be avoided by recognising a situation that is potentially hazardous.

Improper operation or maintenance of the dryer could be dangerous and result in an accident causing injury or death.

Sullair can not anticipate every possible circumstance which may represent a potential hazard. The WARNINGS in this
manual cover the most common potential hazards and are therefore not all-inclusive. If the user employs an operating
procedure, an item of equipment or a method of working which is not specifically recommended by Sullair he must ensure
that the dryer will not be damaged or made unsafe and that there is no risk to persons or property.

Your attention is drawn to the pre-use checklist and commissioning information found within this dryer Installation and
Maintenance Instructions

IMPORTANT

SAFETY SIGNS

Operations or procedures involving specific hazards which could cause injury or death if precautions are not heeded, are
identified by the following symbols which are displayed on the desiccant air dryer to indicate potential danger points.

CAUTION : RISK OF ELECTRIC SHOCK

WARNING : RISK OF DANGER

CAUTION : RISK OF HIGH PRESSURE

IT IS STRONGLY RECOMMENDED THAT THE OPERATING INSTRUCTIONS FOR THE PARTICULAR CONTROL
SYSTEM AND THESE INSTALLATION AND MAINTENANCE INSTRUCTIONS ARE READ THOROUGHLY BEFORE
PROCEEDING ANY FURTHER.

PLEASE NOTE: YOUR WARRANTY MAY BE INVALIDATED IF THE EQUIPMENT HAS NOT BEEN INSTALLED,
COMMISSIONED OR MAINTAINED BY Sullair OR ITS APPROVED AGENTS.

Содержание SM-1100N

























Отзывы: